background image

WARNING! 

NEVER START WORK UNLESS THE 

CHAIN AND BAR ARE LUBRICATED.

3.  SAW CHAIN LUBRICATION

2.  TENSIONING THE CHAIN

1.   Place the telescopic 

pole pruner on a level 

surface.

2.   Clean the area around the oil  

tank cap and then open it.

3.   Fill the oil tank with BAR AND 

CHAIN OIL (not supplied) to 

maximum fill line. Do not overfill 

in doing so, make sure that no 

dirt gets into the oil tank. This will 

ensure that the oil nozzle does 

not clog.

4.  Close the oil tank cap.

MAX.

MAX.

MAX.

WARNING!:

 THE USE OF THE POLE PRUNER 

WITHOUT BAR AND CHAIN OIL OR WITH AN OIL 

LEVEL BELOW THE MINIMUM OIL LEVEL MARK WILL 

RESULT IN DAMAGE TO THE CHAIN!

1.    Loosen the chain cover 

lock. Do not remove the 

side cover.

2.   Adjust the chain tension with the 

chain tensioning dial. Turning 

the dial CLOCKWISE increases 

the chain tension, turning it 

COUNTER-CLOCKWISE 

decreases the chain tension.

3.   For the correct chain tension, 

firmly pull up on the chain at the 

middle of the top of the exposed 

guide bar. When the chain is 

pulled up to its highest point, the 

bottom tip of the links should only 

just stay in the track [middle of the 

guide bar]

4.   After the chain has been 

accurately tensioned, lock 

the guide bar in place with 

the chain cover lock.

5.   Check the tension again 

after a few minutes of cutting and several times in the first hour 

because the chain will lengthen as it breaks in. Adjust as you go. A 

loose chain causes rapid wear to both the chain and the guide bar 

and could derail causing a major safety hazard.

NOTE

:

 Proper tension of the chain is extremely important and must be 

checked before starting, as well as during any cutting operation. Taking 

the time to make adjustments to the chain will result in improved 

cutting performance and prolonged chain life.

5.  To check the lubricating system, switch on the pole pruner and hold 

it with the guide bar and chain above some light coloured paper 

such as newspaper. A steadily increasing stain caused by oil spray 

shows the lubricating system is working.

NOTE:

 Guide bar oil may leak if the tool is left for long periods. This is 

normal. If the tool is to be left unused for an extended time, drain the 

oil from the tool. Refill before use.

MAX.

CAUTION!:

 IF YOU TRY TO ROTATE THE CHAIN 

TENSIONING ADJUSTMENT DIAL WHILST THE CHAIN  

COVER LOCK IS TIGHT, IT WILL RESULT IN THE CHAIN 

NOT LOOSENING AND POSSIBLE DAMAGE TO THE 

MECHANISM.

MAX.

 

50

50

CAUTION!:

 THE CHAIN HAS SHARP EDGES. FOR YOUR 

OWN SAFETY, PLEASE USE WORK GLOVES.

 

50

50

 

50

50

 

50

50

Содержание EPP-750









Отзывы: