manualshive.com logo in svg

Ozito bsr-800, Инструкция по эксплуатации

Поделиться
Скачать
Ozito bsr-800 Скачать руководство пользователя страница 13

12

MAINTENANCE

•

Regularly empty the dust bag.

•

Keep the ventilation slots of the sander clean at all times. If possible prevent
foreign matter from entering the vents.

•

After each use, blow air through the sander housing to ensure it is free from all
dust particles that may build up. 

CAUTION: Excessive build-up of dust particles may cause the sander to 
overheat and fail.

•

If the enclosure of the sander requires cleaning, use a soft, moist cloth only. Do
not use solvents.

CAUTION: Never immerse any part of the sander in liquid.

Carbon brushes will wear out after many uses, causing the sander to spark and/or
stop. The brushes are a wearing component of the sander and should be replaced
prior to the carbon wearing out completely. Take the sander to a suitably qualified
electrician or power tool repairer for replacement. Always replace both brushes at the
same time.

Note: 

Ozito Industries will not be responsible for any damage or injuries caused by

the repair of the tool by an unauthorised person or by mishandling of the tool.

IMPORTANT:

If the motor on your belt sander operates but the belt does not rotate, follow these
instructions. In most cases, it isn't necessary to return the product back to the store.
Check that the drive belt has not been damaged. If it is damaged or broken, replace
with the spare belt provided. 

1. To remove and check the drive belt, remove the two

screws from the belt cover. (Fig. 11) If the belt is
damaged, worn or broken, replace with a new drive belt. 

2. To remove drive belt, simply use a pair of scissors to cut

the drive belt. 

Note: 

DO NOT pry the belt off the pulley as this may

damage the housing. 

3. To fit the new drive belt, place it around the large belt

wheel. Align the ridges on the belt with the teeth on the
small gear wheel. Rotate the large belt wheel and push
the drive belt down onto the small gear wheel as it rotates.
The wheel can be difficult to rotate until the drive belt is
fed onto the small gear wheel. Keep rotating the wheel
and feed the drive belt onto the small gear wheel until it
sits flush with the edge of the wheels (Fig. 12).

4. Refit cover and tighten screws.

screws

Fig. 11

Fig. 12

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание bsr-800

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды