Ozito 43.008.16, Оригинальная инструкция по эксплуатации

Страница: 18 / 28

GB
- 18 -
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull the
machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the
very back until the saw blade (7) has comple-
tely cut through the workpiece.
•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45° (Fig.
1-3, 12)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14). The saw has locking positions at angles
of - 45°, -31.6°, -22.5°, -15°, 0°, 15°, 22.5°,
31.6° and 45°, at which the turntable (17) au-
dibly clicks into position.
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Cut as described in section 6.1.
6.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 13)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° and to the right of 0°-45° in
relation to the work surface.
•
If required, dismantle the clamping device (8)
or mount it on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (17) in 0° position.
•
Adjust the miter angle on the machine head
as described in section 5.3.
•
Cut as described in section 6.1.
6.4 Miter cut 0°- 45° and turntable 0°- 45° (Fig.
1-3, 14)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° and to the right of 0°-45° in
relation to the work surface, with simultaneous
setting of the turntable from 0°-45° to the left or
0°-45° to the right in relation to the stop rail (dou-
ble miter cut).
•
If required, dismantle the clamping device (8)
or mount it on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.2).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
as described in section 5.3.
•
Cut as described in section 6.1.
6.5 Limiting the cutting depth (Fig. 15)
•
If the stop (28) is aligned parallel to the saw
blade (4), the cutting depth limiter will be
deactivated.
•
To activate the cutting depth limiter, the stop
(28) must be swung to the right.
•
The cutting depth can be infinitely adjusted
using the screw (27). Turn the screw (27) in or
out to set the required cutting depth and then
retighten the knurled nut on the screw (27).
•
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (22) for
sawdust and chips.
The sawdust bag (22) can be emptied by means
of a zipper at the bottom.
6.7 Replacing the saw blade (Fig. 1, 16)
•
Warning! Before changing the saw blade:
Pull out the power plug!
•
Caution! Wear work gloves to prevent injury
when changing the saw blade.
•
Swing the machine head upwards (4).
•
Undo the screw (44) on the cover plate (43)
of the saw blade.
•
Pull back the adjustable blade guard (6) and
at the same time turn the cover plate to achie-
ve access to the flange bolt.
•
Push up the cover plate (43) far enough for
you to be able to screw in the screw (44)
Anl_SCMS_2125U_SPK7.indb 18 Anl_SCMS_2125U_SPK7.indb 18 02.12.2019 11:25:14 02.12.2019 11:25:14