background image

GB

- 11 -

out downwards.

• 

 Carefully clean the flange screw (31), outer 

flange (32) and inner flange.

• 

 Fit and fasten the new saw blade (5) in rever-

se order.

• 

 Important. The cutting angle of the teeth, in 

other words the direction of rotation of the 

saw blade (5) must coincide with the direction 

of the arrow on the housing.

• 

 Check to make sure that all safety devices 

are properly mounted and in good working 

condition before you begin working with the 

saw again.

• 

 Important. Every time that you change the 

saw blade, check to see that it spins freely in 

the table insert (22) in both perpendicular and 

45° angle settings.

• 

 Important. The work to change and align the 

saw blade (5) must be carried out correctly.

7. Replacing the power cable

Danger!

 

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

8. Cleaning, maintenance and 

ordering of spare parts

Danger!

 

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon 

brushes checked only by a quali

fi

 ed electrician.

Important! The carbon brushes should not be re-

placed by anyone but a quali

fi

 ed electrician.

8.3 Maintenance

• 

There are no parts inside the equipment 

which require additional maintenance.

• 

 Lubricate all moving parts at regular intervals.

8.4 Ordering spare parts and accessories

Please provide the following information when 

ordering spare parts:

• 

Type of unit

• 

Article number of the unit

• 

ID number of the unit

• 

Spare part number of the required spare part

For our latest prices and information please go to 

www.isc-gmbh.info

Tip! For good results we 

recommend high-quality ac-

cessories from 

www.kwb.eu 

[email protected]

9. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw 

materials in this packaging can be reused or 

recycled. The equipment and its accessories are 

made of various types of material, such as metal 

and plastic. Never place defective equipment in 

your household refuse. The equipment should 

be taken to a suitable collection center for proper 

disposal. If you do not know the whereabouts of 

such a collection point, you should ask in your 

local council o

  ces. 

10. Storage

Store the equipment and accessories out of 

children’s reach in a dark and dry place at above 

freezing temperature. The ideal storage tempe-

rature is between 5 and 30 °C. Store the electric 

tool in its original packaging.

Anl_CMS_1621_U_SPK7.indb   11

Anl_CMS_1621_U_SPK7.indb   11

04.11.2019   06:39:11

04.11.2019   06:39:11

Содержание 43.002.99

















Отзывы: