STEP 1:
Spread tent out flat, floor side down.
Unzip doors.
NOTE:
The tent includes two removable divider curtains which can be attached
to the inside of the tent to divide it into three rooms.
IMPORTANT:
WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE
GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.
NOTE:
PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE HOW
YOUR FRAME IS ASSEMBLED.
TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN AREA FOR
THE CAMPSITE. TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE DOORS TO
ALLOW AIR TO ENTER THE TENT.
TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, IT IS ADVISABLE
TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY
ONLY TO THE INSIDE SEAMS OF THE TENT AND UNDERSIDE OF THE TENT
FLY. IF APPLIED TO THE OUTSIDE OF SEAMS, DISCOLORATION OF YOUR
TENT MAY OCCUR. SEAM SEALER IS AVAILABLE IN THE CAMPING SECTION
OF ANY LOCAL SPORTING GOODS STORE.
ASSEMBLY INSTRUCTIONS
M O D E L
W969 - 16 Person Cabin Tent
STEP 6:
Attach the plastic corner joints (E & F) to the end of each
fiberglass pole. The smaller opening of the corner joints with
“teeth” fit over the ferrules on the fiberglass pole ends.
Tent should appear
as shown.
Tent should appear
as shown.
STEP 2:
Stake the tent to the ground by inserting tent stakes through
the webbing loops and steel rings at the base of the tent. Hammer
stakes into the ground at a 45° angle to the tent, making sure the tent
floor is pulled out even and tight.
STEP 3:
Extend the fiberglass poles by pulling out each section and placing pole ends
into the metal ferrule connectors. You will have five fiberglass poles. The four long poles
will be used on the roof of the tent. The shorter pole will be used for the front awning.
STEP 4:
Insert the two longest fiberglass
poles (A) into the grey pole sleeves at the
top of the tent roof. Position poles so that
equal pole lengths extend from each end
of the pole sleeves.
STEP 5:
Insert the two fiberglass poles (B) with the red tape on the ends into the
red pole sleeves on the tent roof. Position poles so that equal pole lengths extend
from each end of the pole sleeves.
STEP 7:
Flex the fiberglass poles and attach the corner joints at the other end of
each of the four roof poles.
STEP 8:
Locate and extend the eight steel poles (D), by pulling out each wire-corded
section and placing the jointed ends into the connected pole sections.
STEP 9:
With an adult at each corner on one side of the tent, insert the end
of the steel upright poles into the bottom opening of the plastic corner joints.
STEP 10:
Each adult should lift up on the steel pole and while raising
one side of tent, place the bottom end of the steel pole over the metal pins
located on the rings at the base of the tent. Repeat with the six remaining
main upright poles. Working from one end of the tent to the other.
STEP 11:
Clip the plastic hooks on the tent walls around the steel poles.
STEP 12:
Insert the front awning pole (D) into the red sleeve on the awning
located above the front door. Flex the fiberglass fly pole and insert each end
into the metal grommets located on either side of the front door.
STEP 13:
Stake down the front of the awning by
inserting the stakes though the stake loops and
hammering the stakes into the ground at a 45° angle.
STEP 14:
Unfold fly and place over tent. Attach the hooks
on the fly corners to the metal rings at the base of the tent.
STEP 15:
Secure the fly to the tent by wrapping the Velcro fasteners
at each corner of the fly around the metal tent poles as well as
securing the ties on the underside of the fly to the corner joints.
STEP 16:
Guy ropes have been provided for the fly. Extend
each of the guy ropes which are attached to the fly edges.
Make a loop at the opposite end of the guy rope, by using
slider as shown and place loop over a tent stake. Adjust
slider to make the guy rope tight and stake to the ground.
STEP 17:
There is a mud mat attached to the front of the tent to help keep your
tent floor clean. Insert the stakes through the webbing loops at the front corners
of the mud mat and stake to the ground.
B
F
F
E
E
E
E
F
F
B
C
C
D
C
C
C
C
C
C
A
A
NOTE :
To take down tent, follow steps above in the reverse order. Be sure to leave
doors and windows unzipped. Place stakes into stake bag and poles into the pole bag,
which are provided.
Make sure tent is clean and dry before storing.
The tent
should be folded into equal parts toward the center of the tent to distribute the bulk.
Start a small tight roll, the width of the carry bag, with the pole bag placed at the
end opposite the door. Roll tent toward door to allow air to escape. Once rolled, tie
a string or rope around tent to hold into place. Place tent, frame and stakes into carry bag.
