manualshive.com logo in svg

oxycom 3800OXYSTD, Руководство пользователя

Поделиться
Скачать
oxycom 3800OXYSTD Скачать руководство пользователя страница 53

Version 1.3, 2021-12-14

53

1

2

3

4

5

5

Operation procedures

5.1

How to operate the IntrCooll®

5.1.1

Checks before starting

Before starting make sure that:
-

All panels and covers of the IntrCooll® are installed.

-

There is no marking on the IntrCooll® ‘DO NOT START’.

-

There are no loose or strange parts within the IntrCooll®.

-

The water supply to the IntrCooll® is connected.

-

The correct filters are installed.

-

The correct flow regulator cap (50 Hz / 60 Hz) is installed.

-

The drain is connected to a local drain circuit

-

The IntrCooll® is connected to the mains power supply.

-

The maintenance switch is in ON position.

-

The padlock switch is in ON postion.

-

The thermostat is switched on and connected to the IntrCooll®.

-

For correct settings, refer to the enclosed documentation in the thermostat
package.

5.1.2

Check unit installation

Check and finish filling in the Installation checklist on page 48.

Содержание 3800OXYSTD





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды