OXTS xNAV650 страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 42

background image

Oxford Technical Solutions Ltd. http://www.oxts.com

Page 17 of 42

Digital I/O

Table 9: Digital I/O electrical specifications

I/O

Typical

Min

Max

Input Low Voltage (V)

-

-20

0.5

Input High Voltage (V)

-

2

20

Output Voltage high (V)

3.3

2

3.3

Output Voltage Low (V)

0

-

0.8

Output Current (mA)

-

-

4

Note that triggers are pulled up internally to allow a switch to be used to short them to GND.

User cable

The standard xNAV650 user cable is designed for quick access to the main interfaces. Figure 7 shows
the cable diagram and Table 11 shows the pin descriptions for the interface connectors. At the end of
this manual there is a full page drawing of the user cable provided.

Power lines should be correctly terminated and insulated and wired up with a fuse somewhere between
the unit and power source before being connected to a power source. The user must again perform a
visual inspection of the cable equipment before use to ensure there is no damage.

Figure 7: xNAV650 user cable

«
...
15
16
17
18
19
...
»

Содержание xNAV650











































Отзывы:

Нет отзывов

Похожие инструкции для xNAV650

Бренд: iDataLink Страницы: 9

Бренд: Boss Audio Systems Страницы: 34

Infotainment Navigation Columbus

Бренд: Skoda Страницы: 96

EcoZone ConServer

Бренд: IrriGreen Страницы: 29

AZERA/GRANDEUR HD

Бренд: Hyundai Страницы: 13

Бренд: flexvision Страницы: 32

Бренд: Audiovox Страницы: 6

Бренд: Pioneer Страницы: 9

Бренд: Pioneer Страницы: 10

Бренд: Pioneer Страницы: 27

Бренд: Pioneer Страницы: 37

Бренд: Pioneer Страницы: 40

Бренд: Pioneer Страницы: 64

Бренд: Pioneer Страницы: 64

Бренд: Pioneer Страницы: 101

Бренд: Pioneer Страницы: 155

Бренд: Pioneer Страницы: 195

Бренд: Pioneer Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды