OXTS xNAV650 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 42

OXTS xNAV650 Скачать руководство пользователя страница 36

Oxford Technical Solutions Ltd. http://www.oxts.com

Page 36 of 42

Table 17: Time epoch advanced commands

GPS

-ptp_time_mode_gps

Unix

-ptp_time_mode_unix or -ptp_custom_offset_315964800

UTC

-ptp_time_mode_utc or -ptp_custom_offset_315964782

PTP

-ptp_time_mode_ptp or -ptp_custom_offset_315964819

Here you can see that the different time modes can be reached by adding different offsets to the GPS
timestamps. Similarly, the -ptp_custom_offset_%d command can also be used to access time modes
not listed above by finding the correct offset (which will be the number of seconds between the different
epochs).

During internal testing of the PTP feature, a data was collected with a Hesai Pandar40P and an RT3000
v3. Time synchronisation was achieved using PTP. The RT3000 v3 was in GPS mode but the Hesai
Pandar40P was expecting timestamps in UTC. The following command was required to generate an
accurate pointcloud:

lidar_time_offset=315964785000000000

If the RT3000 v3 was instead in Unix time mode, the following command would be required:

lidar_time_offset=-18000000000

Finally, ensure that your survey device is correctly configured to anticipate PTP time synchronisation.

Cable modification

The standard user cable for the xNAV650 is shown in Figure 7. This has been made to be ideal for
modification to the user’s selected purpose. Using the cable wiring diagram and the wiring guide shown
at the end of this document you will be able to wire up a cable with a suitable connector to interface
with whichever requirements you have. If you are creating your own cable you will need to ensure that
the same micro-d connector is used and the pinouts are correctly configured.

OxTS does not guarantee the functionality of any modifications made to the user cable and is not
responsible for any damage caused to the INS or other devices.

«
...
34
35
36
37
38
...
»

Содержание xNAV650











































Отзывы:

Нет отзывов