background image

 

 

 

Oxford Technical Solutions Ltd. http://www.oxts.com 

Page 3 of 42 

 

 

Warranty 

Oxford  Technical  Solutions  Limited  warrants  its  products  to  be  free  of  defects  in  materials  and 
workmanship, subject to the conditions set forth below, for a period of one year from the Date of Sale. 

“Date of Sale” shall mean the date of the Oxford Technical Solutions Limited invoice issued on delivery 
of the product. The responsibility of Oxford Technical Solutions Limited in respect of this warranty is 
limited solely to product replacement or product repair at an authorised location only. Determination of 
replacement or repair will be made by Oxford Technical Solutions Limited personnel or by personnel 
expressly authorised by Oxford Technical Solutions Limited for this purpose. 

In  no  event  will  Oxford  Technical  Solutions  Limited  be  liable  for  any  indirect,  incidental,  special,  or 
consequential damages whether through tort, contract or otherwise. This warranty is expressly in lieu 
of  all  other  warranties,  expressed  or  implied,  including  without  limitation  the  implied  warranties  of 
merchantability  or  fitness  for  a  particular  purpose.  The  foregoing  states  the  entire  liability  of  Oxford 
Technical Solutions Limited with respect to the products herein. 

Any use or misuse of the product in a manner not intended may impair the protection provided. Please 
contact OxTS if you believe any service or repair is required on your product. 

 

 

Содержание xNAV650











































Отзывы: