Overhead door CD Series Скачать руководство пользователя страница 24

Страница: 24 / 32

WARNING

During the following steps, the motor protector may
open. Wait about 20 minutes for protector to reset.
1. Adjusting the

“

OPEN

”

limit switch (Fig. 8-1).

•

Run door to open position by pushing wall control.

•

Locate curved

“

OPEN

”

limit adjustment slot on

back of power head.

•

Look into slot for pinion screw.

•

Insert a screwdriver and turn pinion screw.

–

clockwise to open more.

–

counterclockwise to open less.

2. Test door operator. Use wall control to run
door open and close.
3. Repeat step as necessary to properly set

“

OPEN

”

limit switch.

4. Adjust the

“

CLOSE

”

limit switch (Fig. 8-1).

•

Run door fully closed by pushing wall control.

•

Locate curved

“

”

limit adjustment slot on

back of power head.

•

Look into slot for pinion screw.

•

Insert a screwdriver and turn pinion screw.

–

counterclockwise to close more.

–

clockwise to close less.

5. Test door operator. Use wall control to run door

open and close

6. Repeat step as necessary to properly set

“

CLOSE

”

limit switch

7. Perform CONTACT REVERSE

Moving door can cause serious injury or death

•

Keep people clear of opening while door is moving.

•

Do Not allow children to play with remote controls.

If safety reverse does not work properly:

•

Close door and disconnect operator using
emergency release.

•

Do not use door operator or remote controls

•

Refer to door and door operator owner

’

Manuals before attempting any repairs

NOTE: Factory sets different codes for each remote con-
trol.
Remote controls will not work if STB

’

s malfunction

When programming remote control keep at least 24 inch-
es away from antenna.

1. Program one-button remote (Fig. 9-1)

•

Locate learn code button and learn indicator on
power head.

–

Remove lens cover on back of power head.

•

Press and release learn code button on

power head.

–

LED on power head blinks 2 times per second.

One-Button Remote Control*

Multi-Button Remote Control*

Complete with

Battery

Actual picture may vary by model

NEC

CLASS 2

MORE
FORCE

PUSH
BUTTON

SAFETY
BEAM

LIMIT
SET

OPEN
FORCE

CLOSE
FORCE

RADIO
SIGNAL
LEARN
CODE

COM

DO NOT
PUSH
LIMIT SET
UNLESS
DOOR IS

ATTACHED

NOTE:

USE ONLY WITH

SERIES II CONTROLS

CLOSE
MORE

OPEN
MORE

OPEN

LIMIT ADJUSTMENT

U.S. Patent No. 5,243,784

5,221,869

MORE

LIMIT ADJUSTMENT

CLOSE

OPEN

PUSH

LIMITS

TO SET

CLASS 2

NEC

STEALTH

PRO-MAX

Fig. 9-1

...

FINE LIMIT SWITCH ADJUSTMENT

FOR HELP—1-800-929.3667 OR OVERHEADDOOR.COM

MORE

LIMIT ADJUSTMENT

CLOSE

OPEN

PUSH

LIMITS

TO SET

CLASS 2

NEC

LIMIT ADJUSTMENT

CLOSE

MORE

OPEN

MORE

LIMIT ADJUSTMENT

CLOSE

OPEN

PUSH

LIMITS

TO SET

CLASS 2

NEC

LIMIT ADJUSTMENT

CLOSE

MORE

OPEN

MORE

Fig. 8-1

...

REMOTE CONTROLS

* Remotes vary depending on model. Your operator will
have one or the other.

(continued on next page)

Содержание CD Series

































Результаты поиска

Содержание CD Series

Отзывы:

Похожие инструкции для CD Series

Бренды по названию

Популярные бренды

Overhead door CD Series, Руководство пользователя

Результаты поиска

Содержание CD Series

Отзывы:

Похожие инструкции для CD Series

Бренды по названию

Популярные бренды