Outlaw Ultra-X12, Руководство пользователя, Страница: 8 / 16

Outlaw Audio 8
Use only with a 250v fuse
Employer uniquement avec
un fusible de 250v
RIGHT LEFT
120V - 60HZ
5A
T 5A L 250V
MODEL Ultra-X12
POWERED SUBWOOFER
CAUTION
AVIS: RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PASS-THRU TO
LOUDSPEAKERS
RIGHT LEFT
HIGH LEVEL INPUTS
FROM AMPLIFIER
(INTERNAL X-OVER)
POWER
POWER PHASE
VOLUME
THRU
INTERNAL
X-OVER
FREQUENCY
(HZ)
SUB IN
INTERNAL
X-OVER
0°
180°
OFF
AUTO
ON
MIN MAX 60 120
PORT
MODE
MAX OUTPUT
MAX EXTENSION
L
R
SUB IN
EXTERNAL
X-OVER
ON
AC FUSE
OFF
MASTER POWER
CAUTION
FOR CONTINUED
PROTECTION AGAINST
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE AND RATING
Connecting to a System with a Subwoofer Preamp Output
If a low-level subwoofer output is available, use one of the
SUB IN jacks on the rear panel of the Ultra-X12 to connect
to your Preamp/Processor or Receiver. Any audio device that
decodes Dolby Digital or DTS soundtracks will have this type
of jack. Depending on the particular brand or model, this RCA
jack may be labeled “Sub,” “Subwoofer,” or “LFE Out.”
The choice of which SUB IN jack depends on whether you
want to use the Ultra’s internal crossover, or an external
crossover, such as the one in your Preamp/Processor or
other bass management system, to process the subwoof-
er’s audio input.
The information in this section contains some of the
more common subwoofer connections. If your receiver or
processor does not have this type of output you will need
to follow the “Connecting to a System with No Preamp
Outputs” instructions on the next page.
CAUTION: Before you make any connections to the
Ultra-X12, please make sure to turn off all system
components and unplug the processor or receiver and the Ultra
from their AC power source.
Connection from Receiver or Pre/Pro using the
Receiver or Pre/Pro's Crossover
Ultra-X12 Low-level Inputs Connection from Receiver or Pre/Pro using the
Subwoofer 's Crossover
¼
To connect the Ultra-X12 to a Receiver or Processor
with a Subwoofer/LFE preamp output and an inter-
nal crossover:
1.
Make sure all system components are off and the
processor or receiver and Ultra-X12 are unplugged
from their AC power source.
2.
Connect a subwoofer cable from the Subwoofer/LFE
output on the receiver or processor to either of the
SUB IN EXTERNAL X-OVER jacks on the rear panel of
the Ultra-X12.
3. To connect two subwoofers to a receiver or proces-
sor with a single subwoofer output, use the Ultra’s
THRU jack to daisy chain to the next subwoofer.
Alternatively, you can use a Y-adapter to connect two
subwoofers to a single Subwoofer/LFE output.
4.
Proceed to the “Power Connection” section on
page 10.
¼
To connect the Ultra-X12 to a Receiver or Processor
with a Subwoofer/LFE preamp output, but without
an internal crossover:
1.
Make sure all system components are off and the
processor or receiver and Ultra-X12 are unplugged
from their AC power source.
2.
Connect a subwoofer cable from the Subwoofer/
LFE output on the receiver or processor to the SUB
IN INTERNAL X-OVER jack on the rear panel of the
Ultra-X12.
You can use either the Left or Right SUB IN INTERNAL
X-OVER jack.
3.
Proceed to the “Power Connection” section on
page 10.
THRU
SUB IN
EXTERNAL
X-OVER
SUB IN
INTERNAL
X-OVER
L
R
Ultra-X12 Rear Panel
Preamp/Processor
Receiver
Additional Powered
Subwoofer(s)
(not supplied)