background image

Outdoor Living Today         www.outdoorlivingtoday.com          [email protected]

8x8 Sunshed Garden Shed 

Assembly Manual

Outdoor Living Today

Thank you for purchasing a 8x8 Sunshed Garden Shed from Outdoor Living Today.  Please
take the time to identify all the parts prior to assembly.  

Safety Points and Other Considerations
Our products are built for use based on proper installation and normal residential use, on level ground. Please
follow the instruction manual when building your shed and retain the manual for future maintenance
purposes.

Some of the safety and usage measures you may wish to consider include:

-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the
snow off the roof(s). 
-if the product is elevated, any structural and building code requirements are solely the customer's 
responsibility, and should be abided by. 
-in high or gusty wind conditions it is advisable to keep the structure securely grounded. 
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight. 

Customers agree to hold Outdoor Living Today and any Authorized Dealers free of any 
liability for improper installation, maintenance and repair of any Outdoor Living Today 
products.

Page 1

Revision #2
April 2007

Содержание 8x8 Sunshed Garden Shed






























Отзывы: