Outback GTFX2012E Скачать руководство пользователя страница 23

Страница: 23 / 56

AC WIRING NOTES

AC HOT OUT

• AC hot output conductor (brown) wire

gauge must be sized to the breakers and
loads

AC NEUTRAL OUT/AC NEUTRAL IN

• Both neutral terminals are common with

each other within the FX.

• Only one neutral needs to connect at the

terminal if a separate common neutral bus
bar is installed.

CHASSIS GROUND

• Both CHASSIS GROUND terminals are

common within the FX.

• The AC input and AC output ground

wires can connect to these terminals, or
one ground wire can be connected if a
common ground bus bar is installed.

AC HOT IN

• The AC hot input conductor (brown) must

be supplied through an appropriately-
sized AC branch rated circuit breaker.

• 10.0 mm

(8 AWG) or larger wire is

recommended to accommodate the FX’s
AC transfer relay.

13.3 mm

(6 AWG) is the largest size of wire

that can be used with the input or output
terminals.

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Содержание GTFX2012E

























































Результаты поиска

Содержание GTFX2012E

Отзывы:

Бренды по названию

Популярные бренды

Outback GTFX2012E, Руководство по установке

Результаты поиска

Содержание GTFX2012E

Отзывы:

Бренды по названию

Популярные бренды