Oursson TP3310PD, Инструкция по эксплуатации

Страница: 14 / 88

14
UTILIZATION,
Рiс. С
Control panel,
Рiс. С-1
1. BOILING
button
2. TIMER
button
3. TEMPERATURE
button
4. POUR
button
5. UNLOCK
button
6. Unlock indicator
7.
Display
Display,
Рiс. С-2
1. Water temperature indication
2. Timer
3. Temperature selection indication
4.
Unlock indication flashes when unlocked
5. Lock indication
6.
Timer indication flashes when sets
7.
Boiling/re-boiling indication flashes when one of the
functions is on
8. BOILING indication
9.
WARM UP indication
Thermo pot is design only for heating clean drinking
water.
You can use thermo pot in the following modes:
• Heating water to a predetermined temperature;
• Maintain selected water temperature;
• Boil water.
Never fill thermo pot directly from the tap, because
the water spray can get into the device or control
panel and cause a short circuit, electric shock or
malfunction of the device.
Boiling,
Рiс. С-5
1.
Plug in the device.
2.
Boiling will start automatically, indication will light
up. Display will show the current water temperature.
Temperature will increase step by step.
3.
After boiling, the device will go into a temperature
maintain mode 85
o
C, indication will be lit. When the
temperature will be lowering, automatic warm up turns
on.
Heating water to a predetermined temperature
1.
Fill the device with water. Plug in the device. The display
will show the current temperature. Boiling will start
automatically, indication will light up.
2.
Press button a few times to set the desired heating
temperature of the water. The minimum value of heating is
40° C, maximum - 98° C. Available values are:
40, 50, 65,
85 and 98° C .
3.
While heating, you may change the temperature by
pressing
button.
Before first use:
• Wash the inner surface of the device with the use of non-
abrasive cleaners. Dry the device. Wipe the device with a
clean dry cloth.
• Boil the maximum amount of water. Monitor for no leaks,
sparks, melting of body, excessive heating of the power
cord, plug, and burning smell during first two boiling.
• Boiled water from the first two boiling is not recommended
to use in food. You can use it for everyday needs.
To accelerate the cooling of the heating
element, do not fill the device with cold water.
This may damage the heating element.
First, insert the power cord into the device and only
then insert the plug into the outlet. Violation of this
order may result in electric shock.
The device is equipped with protection from
switch-on without water. If you turn on the
device with no water or less then MIN mark, the
device will turn off after a few seconds. After the
heating element cools, the device will get back to
working condition, POSSIBLE PROBLEMS AND
SOLUTIONS section.
Beware the burst of steam when opening
the lid of the device.
OPERATION ORDER
Filling with water,
Рiс. С-3, С-4
1.
Unlock the lid by pressing the button in the handle,
Pic. C-3
2.
Drag the lid’s handle up.
3.
Fill the inner container with cold water till “
FULL
” mark,
using a kettle or other suitable kitchenware, Pic. C-4
4.
Close the lid till you hear a click.
NOTE!
If you fill the device with hot water, automatic
protection that turns off the heating element may turn on.
Re-boiling
By adding cold water into the thermo pot when it is in
WARM UP
mode, re-boiling mode will automatically start,
indication lights up.
NOTE!
If you will add a small amount of water, re-boiling
function may not start automatically, indication will lit,
press
to start boiling.
After the water is heated to a predetermined temperature,
the device will switch automatically into the
WARM UP
mode, showing the current temperature.
NOTE!
If you will unplug the device for a few minutes and
then plug it again, the device will switch into a
WARM UP
85° C mode.
Water supply,
Рiс. С-6
Make sure the button is unlocked,
indicator is lit up
and
indication flashes. Take a cup for drink and place
it under dispenser.
Method 1:
press and hold button. While you hold the
button, water is supplied through the dispenser. Release the
button to stop water supply. Pic. C-6-1.
Method 2:
with cup press the knob behind the dispenser,
while you press the knob the water supplies through
dispenser. Release the knob to stop water supply.
Pic. C-6-2.
To determine the level of remaining water in the
device, use the scale.
Automatic lock,
Рiс. С-7
The device is equipped with automatic lock from water
supplying and pressing button, the display indication is
. The lock turns on automatically if there are no actions