18w Wing Shade Floor Lamp
T81G5T T81G5T-SHPR
CFO-002
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
STEP 1: PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to: www.ott-lite.
com/warranty.
WARNING:
To prevent electric shock, make sure the lamp is not
plugged in until all assembly steps are complete.
CAUTION: TIP HAZARD. DO NOT MOVE SHADE OR
ACCESSORIES
outside of the shaded area as shown in Figure 1.
Shade and accessories must be kept within the shaded area and
must align in the same forward-facing direction as the base.
LAMP ASSEMBLY
1.
Screw the upper lamp stem (B) into the lower lamp stem (C).
2.
Firmly insert the assembled stem of the lamp into the hole
located in the top of the base (H).
3.
Remove the wrench (G), bolt (F) and washers (D, E) from the
plastic bag (included in the box containing the base).
4.
Insert the bolt (F) through the lock washer (E), then through
the flat washer (D), and finally into the recessed hole in the
bottom of the base (H).
5.
Using the wrench (G) provided, tighten the bolt (F) firmly by
turning clockwise.
TUBE INSERTION/REPLACEMENT
1.
Make sure the lamp is not plugged into an electrical socket.
2.
If the lamp has been in use, allow it to cool for approximately
5 minutes before proceeding.
3.
Set the lamp upright on the floor.
4.
To install a tube (A) in the socket, grasp the tube firmly in your
hand. Clip the tube into the shade clip (M) and push the tube
straight into the socket (N) until it “snaps” into place (O).
Do not apply pressure to the glass end of the tube.
5.
To remove a tube already installed in the lamp, grasp
the tube firmly in your hand and angle it slightly out of the
shade clip (M) approximately 15 degrees (P) and pull it straight
out of the socket. Do not twist or turn the tube while removing
it from the socket.
6.
Position the shade as desired by flexing the neck.
7.
Plug the lamp into a standard 120V socket. Your lamp
is ready for use.
Please note that in operation, OttLite
®
tubes are not
dimmable.
Enjoy your OttLite
®
Wing Shade Floor lamp!
This lighting system is designed for use with OttLite
®
type
(Style Number PL18-B). Use of other products
voids the warranty and may result in damage to the
lighting system.
CAUTION!
If the external flexible cable or cord of
this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or its service agent or a similar qualified person in order
to avoid a hazard. Indoor use only.
CAUTION!
To prevent electric shock,
match wide
blade of plug to wide slot, fully insert.
CAUTION! IMPORTANT
SAFETY INSTRUCTIONS:
This portable lamp has a polarized plug (one blade is wider than the
other) as a feature to reduce the risk of electric shock. This plug will
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless plug can be fully
inserted. Do not alter the plug.
This product complies with Part 18 of FCC Rules, but may cause
interference to radios, televisions, wireless telephones, and
remote controls. Avoid placing this product near these devices. If
interference occurs, move the product away from the device or plug
either into a different outlet. Do not install this product near maritime
safety equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.
ENGLISH
18w Wing Shade Floor Lamp
INS120046 REV111212
ENGLISH
CONGRATULATIONS!
You’ve purchased the finest in natural lighting
technology with your new OttLite
®
product.
STEP 1: PRODUCT REGISTRATION FORM
Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
www.OttLite.com/warranty.
WARNING: To prevent electric shock, make
sure the lamp is not plugged in until all
assembly steps are complete.
CAUTION: TIP HAZARD
DO NOT MOVE SHADE OR ACCESSORIES
outside of the shaded area as shown in
Figure 1. Shade and accessories must be
kept within the shaded area and must align
in the same forward-facing direction as the
base.
STEP 2: LAMP ASSEMBLY
1.
Screw the upper lamp stem (B) into the lower
lamp stem (C).
2.
Firmly insert the assembled stem of the lamp
into the hole located in the top of the base (H).
Note: Depending on the Assembly Package
you receive, use corresponding instructions
for steps 3 to 5.
Assembly Package A:
3.
Remove the wrench (G), nut (F) and washers
(D, E) from the plastic bag (included in the box
containing the base).
4.
Insert the nut (F) over the lock washer (E),
then over the flat washer (D), and finally onto
the recessed bolt in the bottom of the base. (H).
5.
Using the wrench (G) provided, tighten the
nut (F) firmly by turning clockwise.
Assembly Package B:
3.
Remove the wrench (G), bolt (F) and washers
(D, E) from the plastic bag (included in the box
containing the base).
4.
Insert the bolt (F) through the lock washer
(E), then through the flat washer (D), and finally
into the recessed hole in the bottom of the
base (H).
5.
Using the wrench (G) provided, tighten the
bolt (F) firmly by turning clockwise.
STEP 3: TUBE INSERTION/
REPLACEMENT
1. Make sure the lamp is not plugged into an
electrical socket.
2. If the lamp has been in use, allow it to cool
for approximately 5 minutes before proceeding.
3. Set the lamp upright on the floor.
4. To install a tube (A) in the socket, grasp
the tube firmly in your hand. Clip the tube into
the shade clip (M) and push the tube straight
into the socket (N) until it “snaps” into
place (O). Do not apply pressure to the
glass end of the tube.
5. To remove a tube already installed in the
lamp, grasp the tube firmly in your hand and
angle it slightly out of the shade clip (M)
approximately 15 degrees (P) and pull it straight
out of the socket.
Do not twist or turn the
tube while removing it from the socket.
6. Position the shade as desired by flexing the
neck.
7. Plug the lamp into a standard 120V socket.
Your lamp is ready for use.
Please note that in operation, OttLite
®
tubes are
not dimmable.
Enjoy your OttLite
®
Easyview Craft lamp!
This lighting system is designed
for use with OttLite
®
tubes only
(model number T18330). Use of
other products voids the warranty
and may result in damage to the
lighting system.
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D’UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L’AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S’INSÈRE DANS
LA PRISE QUE D’UN SEUL CÔTÉ. SI ELLE N’ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE N’ENTRE
TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N’UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF SI
LA FICHE S’INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA
FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU’AU BOUT.
¡PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA OTRA)
COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE ENCAJARÁ EN
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA COMPLETAMENTE
EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO CON UN ELECTRICISTA
CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA SER TOTALMENTE
INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
Wing Shade Floor Lamp
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
INS90011 REV060109
18w Wing Shade Floor Lamp
K15PNB
V11M47
S6237T
T81G5T
Usable area for shade
Area útil para la pantalla
Zone sécuritaire pour
l’abat-jour
DO NOT USE SHADE
IN THIS AREA
NO UTILICE LA
PANTALLA EN ESTA
AREA
NE PAS PLACER
L’ABAT-JOUR DANS
CETTE ZONE.
FIGURE 1 / FIGURA 1
Assembly Package A:
Assembly Package B:
Usable area for shade
Zone sécuritaire pour
l’abat-jour
Area útil para la pantalla
DO NOT USE SHADE
IN THIS AREA
NE PAS PLACER
L’ABAT-JOUR DANS
CETTE ZONE.
NO UTILICE LA
PANTALLA EN ESTA
AREA
/LWH
2W
W
A
B
C
H
D
E
F
G
FIGURE 1 / FIGURA 1
