background image

Sheet No. 

Issue Date:  Rev. C   September 19, 2011

© SPX

Form No. 538016

Parts List & 
Operating Instructions 
for: 

2510A

Air / Hydraulic Pump

 

Maximum Capacity: 690 bar (10,000 psi)

655 EISENHOWER DRIVE

OWATONNA, MN  55060-0995  USA

PHONE: (507) 455-7000

TECH. SERV.: (800) 533-6127

   FAX: (800) 955-8329

ORDER ENTRY: (800) 533-6127

   FAX: (800) 283-8665

INTERNATIONAL SALES: (507) 455-7223

  FAX: (507) 455-7063

Original Instructions

Description: The 2510A air/hydraulic pump is designed to have a maximum capacity of 690 bar (10,000 psi). 
It has a 2-stage release mechanism, internal relief valve, and 1606 CC (98 cu. in.) of useable oil. It pumps, 
holds, or releases a load with pedal control.

1 of 4

Explanation of Safety Signal Words

The safety signal word designates the degree or level of hazard seriousness.

DANGER

: Indicates an imminently hazardous situation which, if not avoided, will result in death or 

serious injury.

WARNING

: Indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.

CAUTION

:  Indicates  a  potentially  hazardous  situation  which,  if  not  avoided,  may  result  in  minor  or 

moderate injury.

CAUTION

:  Used  without  the  safety  alert  symbol  indicates  a  potentially  hazardous  situation  which,  if  not 

avoided, may result in property damage.

Содержание 2510A









Отзывы: