OSS OSS-EOS-2U-41 Скачать руководство пользователя страница 15

Страница: 15 / 46

One Stop Systems

OSS-EOS-2U-4I

| 15

1.6

Motherboard Features

CPU

Supports two 3rd Gen. Intel Xeon Scalable Processors (in Socket P+ LGA 4189) with up to 38 cores per CPU and a
thermal design power (TDP) of up to 270W

Memory

Supports up to 4 TB of 3DS LRDIMM/LRDIMM/3DS RDIMM/RDIMM DDR4 (288-pin) ECC memory with speeds of
3200/2933/2666 MHz in 16 memory slots and up to 4 TB of Intel Optane PMem 200 Series with speeds of up to 3200
MHz Note 1: The Intel Optane Persistent Memory (PMem) 200 Series are supported by the 3rd Gen. Intel Xeon
Scalable (83xx/63xx/53xx/4314) series processors. Note 2: Memory speed and capacity support depends on the
processors used in the system.

DIMM Size

Up to 256 GB at 1.2V Note: For the latest CPU/memory updates, please refer to our website at
http://www.supermicro.com/products/ motherboard

Chipset

Intel PCH C621A

Expansion Slots

•

One PCIe 4.0 x8 slot (CPU2 Slot11)

• Six PCIe 4.0 x16 slots (CPU1 Slot2 / CPU1 Slot4 / CPU1 Slot9 / CPU2 Slot6 / CPU2 Slot8 / CPU2 Slot10)

• Two PCIe 4.0 x4 M.2 s

lots (supports M-Key 2242, 2260, 2280, and 22110)

• Two PCIe 4.0 x8 SlimSAS ports w/support of two connections each port (P1_NVME0/1, P1_NVME2/3)

Network

•

Two 10G Ethernet LAN ports supported by Intel X550 LAN controller

•

One Dedicated BMC LAN located on the rear I/O panel (via AST2600 BMC)

Baseboard
Management
Controller (BMC)

ASPEED AST2600 BMC

Graphics

Graphics controller & VGA support via ASPEED AST2600 BMC

I/O Devices

Serial (COM) Port

• One (serial port on the rear I/O panel (COM1)

• One front accessible serial port header (COM2)

SATA 3.0

• Eight I

-SATA 3.0 ports at 6 Gb/s (I-SATA0~3, I-SATA4~7)

• Two Intel PCH powered S

-SATA 3.0 Ports with support for

SuperDOM (Disk on Module) devices (S-SATA4, S-SATA5)

Video (VGA) Connections

• One VGA port on the rear I/O panel (VGA2)

• One VGA header on the motherboard for front access (VGA1

Peripheral Devices

• Four USB 3.0 ports on the rear I/O panel (USB2/3, USB4/5)

• One front

-accessible USB header with support for two USB 2.0 ports (USB0/1)

• One front

-accessible USB header with support for two USB 3.0 ports (USB6/7)

• One internal USB 3.0 Type

-A header (USB8)

BIOS

• AMI BIOS

• ACPI 3.0 or later, PCI firmware 4.0 support, BIOS rescue hot

-key, SPI dual/quad speed support, RTC (Real Time

Clock) wakeup, and SMBIOS 3.0 or later

Power
Management

• ACPI power management

• Power button override mechanism

• Power

-on mode for AC power recovery

• Wake

-on-LAN

• Power supply monitoring

System Health
Monitoring

• Onboard voltage monitoring for +/

-12V, +5V/+5V standby, +3.3V, and +3.3V standby

• Onboard temperature monitorin

g for CPU, VRM, LAN, PCH, system, and memory

• 7+1 CPU switch phase voltage regulator

• CPU thermal trip support

• Platform Environment Control Interface (PECI)

Fan Control

• Fan status monitoring via BMC connections

• Single cooling zone

• Low

-noise fan speed control

• Ten 4

-pin fan headers

LED Indicators

• Power LED

• UID/remote UID

• LAN activity LED

• BMC Heartbeat LED

Dimensions

15.12" (W) x 13.2" (L) ATX (384.05 mm x 335.28 mm)

Содержание OSS-EOS-2U-41















































Результаты поиска

Содержание OSS-EOS-2U-41

Отзывы:

Бренды по названию

Популярные бренды

OSS OSS-EOS-2U-41, Руководство пользователя

Результаты поиска

Содержание OSS-EOS-2U-41

Отзывы:

Бренды по названию

Популярные бренды