OSO HOTWATER 1327051, Руководство по установке

Страница: 4 / 24

4
1. GENERAL INFORMATION
1.1 Product Identification
Identification of your product can be found on
the label attached to the product. The label con-
tains information about the product according to
EN 12897: 2016 and EN 60335-2-21, in addition to
other useful data. See Declaration of Conformity
at www.osohotwater.co.uk for more information.
OSO products are designed and manufactured
according to:
• Tank standard EN 12897:2016
• Safety standard EN 60335-2-21
• Welding standard ISO 3834-2
OSO Hotwater AS is certified according to
• Quality ISO 9001
• Environment ISO 14001
• Working Environment ISO 45001
1.2 UKCA marking
The UKCA mark shows that the product complies
with the relevant Directives. See Declaration of
Conformity at www.osohotwater.co.uk for more
information.
The product complies with he directives for:
• Low voltage LVD 2014/35/EU
• Electromagnetic compatibility EMC 2014/30/EU
• Press Equipment PED 2014/68/EU
1.4 General information
Thank-you for purchasing the OSO Ecoline SCE
indirect hot water cylinder.
OSO advise that the electrical cables are fixed in
place prior to the positioning of the cylinder.
This manual gives detailed advice for installation
and should be read carefully prior to fitting any
unvented unit. OSO Ecoline SCE cylinders are not
suitable for gravity fed primary systems. In known
hard water regions, precautions should be tak-
en to prevent limescale formation in hot water
cylinders, in accordance with Building Regulation
Part L, Domestic Heating Compliance Guide.
This OSO cylinder must be installed by a com-
petent person and be installed in compliance
with the OSO Installation and Maintenance In-
structions, all current legislation, codes of prac-
tice and regulations governing the installation of
unvented hot water cylinders in force at the date
of installation.
1.3 Technical Data Sheet
Trade mark
M T.
item no.
Model/identifier
ErP
Rating
Heat
loss W
Storage
volume L
OSO Hotwater AS
1327051
SCE 120 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.5m² B
44
109
OSO Hotwater AS
1327052
SCE 150 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.8m² B
54
142
OSO Hotwater AS
1327053
SCE 180 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.8m² C
61
163
OSO Hotwater AS
1327054
SCE 210 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.8m² C
67
190
OSO Hotwater AS
1327055
SCE 250 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.8m² C
80
239
OSO Hotwater AS
1327056
SCE 300 - 2.8kW @ 230V/3.0kW @ 240V + coil 0.8m² C
89
277
Directive: 2010/30/EU Regulation: EU 812/2013 Directive: 2009/125/EC Regulation: EU 814/2013
Heat loss tested acc. to standard: EN 12897/2016
TDS - Indirect water heater
! CAUTION
This indirect hot water storage tank is intended to be connected to a high efficiency external energy source.
The immersion heaters are intended for backup and supplementary use only. Immersion heaters as sole heat
source should be avoided and would lead to higher energy consumption and higher operating cost.