Osburn MATRIX OB02032 Скачать руководство пользователя страница 3

Page 3

Installation and Operation Manual - Matrix

ENGLISH

As one of North America’s 
largest and most respected 
wood stove and fireplace 
manufacturers, Stove Builder 
International takes pride in the 
quality and performance of all 
its products. 

The following pages provide 
general advice on wood 
heating, detailed instructions 
for safe and effective 
installation, and guidance 
on how to get the best 
performance from this stove.

It is highly recommend that 
this wood burning hearth 
product be installed and 
serviced by professionals who 
are certified by a «Qualified 
Agengy» such as NFI (National 
Fireplace Institute®) or CSIA 
(Chimney Safety Institute of 
America) in the United States 
and in Canada by WETT 
(Wood Energy Technology 
Transfer) or in Quebec 
by APC (Association des 
Professionnels du Chauffage).

Contact local building or fire 
officials about restrictions 
and installation inspection 
requirements in local area.

A building permit might be 
required for the installation of 
this stove and the chimney 
that it is connected to. It 
is also recommended to 
inform your home insurance 
company.

Please read this entire manual 
before installing and using this 
stove. 

A primary alternative heat 
source should be available in 
the home. This heating unit 
may serve as a supplementary 
heat source. The manufacturer 
cannot be responsible for 
additional heating costs 
associated with the use of an 
alternative heat source.

ONLINE WARRANTY REGISTRATION

If the unit requires repairs during the warranty period, proof of purchase must be provided. The 
purchase invoice must be kept. The date indicated on it establishes the warranty period. If it 
can not be provided, the warranty period will be determined by the date of manufacture of the 
product.

It is also highly recommended to register the warranty online at

https://www.osburn-mfg.com/en/warranty/warranty-registration/

Registering the warranty will help to quickly find the information needed on the unit.

THANK YOU FOR CHOOSING 
THIS WOOD STOVE.

If this stove is not 
installed properly, 
combustible materials 
near it may overheat 
and catch fire.

 

 

To reduce the 
risk of fire, follow 
the installation 
instructions in this 
manual. 

Содержание MATRIX OB02032

























































Отзывы: