manualshive.com logo in svg

Ormazabal velatia transforma.dis, Общее руководство по инструкции

Поделиться
Скачать
Ormazabal velatia transforma.dis Скачать руководство пользователя страница 29

IG-168-EN version 05; 17/04/2020

29

General instructions

transforma

.dis: Distribution transformers immersed 

in dielectric liquid up to 3150 kVA

Maintenance 

 

Instructions for retouching paint

The procedure for repairing damaged paint is as follows:

1.  Sanding the affected area

Remove the rust using sandpaper or a suitable scraper, 

until the metal is shiny.

2.  Applying primer

Spray the affected area with a coat of paint which is rich 

in anti-corrosive pigments of aluminium-zinc or similar. 

Ensure that this paint covers the whole area. Shake 

vigorously before applying the spray.
After applying the primer, allow the area to dry for at 

least 15 minutes or for the time and under the conditions 

recommended by the spray paint manufacturer 

(whichever is longer).

Figure 7.2. 

Spray primer

3.  Applying finish paint

Spray on the dry primer, using the same colour as the 

paint finish, covering the area. Excess paint is removed 

with a damp cloth.

Please contact 

Ormazabal

 to determine the exact 

colour of the spray paint.

Figure 7.3. 

Spray primer

Содержание velatia transforma.dis





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды