background image

TECHNICAL DESIGN FEATURES

page 11

1.

Power LED - lights up when the amplifier is on

2.

Low-pass crossover frequency control-adjusts the front channel
low-pass crossover frequency

3.

Low-pass crossover switch-activates the front channel low-pass
crossover

4.

INTELLiQ gain-adjusts the level of INTELLiQ from 0dB to 10dB of
boost.

5.

High-pass crossover “x10” switch-changes the high-pass crossover
frequency range

6.

High-pass crossover frequency control-adjusts the front channel
high-pass crossover frequency

7.

High-pass crossover switch-activates the front channel high-pass
crossover

8.

Front Gain Control - continuously adjusts from  200mV to 5Vrms
for full power output

9.

Front Output Configuration Switch - determines the output
configuration for the front channels

10. Front RCA Inputs- accepts RCA input from a source unit, preampli-

fier or equalizer for the front channels

11. Rear RCA Inputs- accepts RCA input from a source unit, preampli-

fier or equalizer for the rear channels

12. 2-Channel / 4-Channel Switch - configures the amplifier for two or

four RCA inputs

13. Rear Output Configuration Switch - determines the output

configuration for the rear channels

14. Rear Crossover Control - adjusts the frequency for the rear

channels

15. Rear channel input configures rear channels for direct input or

output of front channel crossover and gain

16. Rear Gain Control - continuously adjusts from  200mV to 5Vrms for

full power output

17. Rear Crossover Switch - configures the rear channel for high-

pass, low-pass or full range operation

18. REM Remote Turn-on Input - turns on the amplifier when fed 12

V+

19. Front speaker output- allows up to 12 gauge speaker wire
20. Rear speaker output- allows up to 12 gauge speaker wire
21. Remote Gain-allows dashboard control of the amplifier output

level

22. Fuse - protects the amplifier from over current situations
23. Power Connections - allow up to 4 gauge power and ground cables

1 2

6

7 8

9

10

11

12

16

14

17

15

13

5

4

3

18

19

20

21

23

22

Содержание XTREME 600.4













































Отзывы: