background image

http://www.orion.ua

  4

  The kettle may be switched “OFF” at any time by pressing the switch on the handle

to the “OFF” position.

  IMPORTANT: Make a habit of switching the power “OFF” at the power outlet before

removing or replacing the kettle on the base or when the kettle is not attended.

  Do not use hot tap water to fill the kettle. Use only cold water. Allow the cold water to

run for three to four seconds before filling the kettle.

  If any plastic taste from the kettle is found it can be removed by filling the kettle to

maximum and adding a teaspoon of bicarbonate of soda to the water.  Boil and
discard the water, rinse out with cold water.

AUTOMATIC SAFETY CUT-OUT

An automatic cut out is fitted for protection against boil-dry overheating. It will operate if
the kettle is switched on when containing insufficient water. If this should occur, switch
off and remove the power cord from the power outlet. Allow the kettle to cool for 10
minutes then refill with cold water and connect to power supply.

CARE OF YOUR PRODUCT

Avoid the use of solvents, polish, abrasive or aerosol cleaners as they may
damage surfaces of the   product. The inside of the kettle may be cleaned using
a mild detergent, however it must be   thoroughly  rinsed  before  re-use.  Clean
the exterior of the kettle by wiping with a slightly

dampened soft cloth. Make

sure the kettle is thoroughly dried before reconnecting to the power

supply.

NOTE: Do not immerse the base or kettle in water or any other liquid.
Furring up is a common problem in hard water areas, and it is recommended to
descale the kettle   regularly. To descale, fill the kettle with 1L of water and add
50ml vinegar. Bring to the boil and allow to stand overnight. Next day, reboil and
pour away and refill the kettle with fresh water, and bring to the boil again. This
water must also be poured away.
NOTE: Normal commercial descalers for kettles may also be used. Follow the

instructions for the  given descaler.

SERVICE

Do not operate the kettle with a damaged cord or plug, or after the kettle
malfunctions, or appears   damaged in any manner. Return the complete kettle to
the place of purchase or address noted in warranty information for inspection,
repair or replacement.
In some products, the replacement by the user of the flexible cord is not

intended. Special tools are required to dis-assemble the product or replace the cord.

Return the complete product to the place of purchase or address noted in
warranty information for inspection, repair or replacement.

CAUTION: To reduce the risk of electric shock, do not dis-assemble the product.
No user serviceable parts inside. Refer all service to an authorised service
facility.

Subject to change without notice

Extra information on ORION company web-site

www.orion.ua

We take your opinion and offers by E-mail

[email protected]

Содержание ORK-0334

Страница 1: ...http www orion ua U US SE ER R S S M MA AN NU UA AL L W WA AT TE ER R K KE ET TT TL LE E O OR RI IO ON N M Mo od de el l O OR RK K 0 03 33 34 4 E En ng gl li is sh h ...

Страница 2: ... same voltage frequency and rating as indicated on the product rating label This appliance is not intended for use by persons including children with reduced physical sensory or metal capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the applince by a person responsible for their safety Children should be supervised to ensure ...

Страница 3: ...t fill above the MAX mark The first time the kettle is used or it has been unused for a long period of time it is recommended that the kettle be rinsed filled to maximum and boiled The water should then be discarded the kettle rinsed and refilled with cold water CAUTION If the kettle is overfilled there is a danger that boiling water may be ejected from the spout Place the cordless base on a dry l...

Страница 4: ... dampened soft cloth Make sure the kettle is thoroughly dried before reconnecting to the power supply NOTE Do not immerse the base or kettle in water or any other liquid Furring up is a common problem in hard water areas and it is recommended to descale the kettle regularly To descale fill the kettle with 1L of water and add 50ml vinegar Bring to the boil and allow to stand overnight Next day rebo...

Отзывы: