ORiNG TRGPS-9084GT-M12X-BP2-MV Скачать руководство пользователя страница 124

Страница: 124 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

123

Other Info

This section contains information about the state of the server and the

latest round-trip

time.

5.8.6 NAS (802.1x)

A NAS (Network Access Server) is an access gateway between an external communications

network and an internal network. For example, when the user dials into the ISP, he/she will be

given access to the Internet after being authorized by the access server. The authentication

between the client and the server include IEEE 802.1X- and MAC-based.

The IEEE 802.1X standard defines a port-based access control procedure that prevents

unauthorized access to a network by requiring users to first submit credentials for

authentication. One or more backend servers (RADIUS

)

determine whether the user is allowed

access to the network.

MAC-based authentication allows for authentication of more than one user on the same port,

and does not require the users to have special 802.1X software installed on their system. The

switch uses the users' MAC addresses to authenticate against the backend server. As

intruders can create counterfeit MAC addresses, MAC-based authentication is less secure

than 802.1X authentication.

Overview of 802.1X (Port-Based) Authentication

In an 802.1X network environment, the user is called the supplicant, the switch is the

authenticator, and the RADIUS server is the authentication server. The switch acts as the

Содержание TRGPS-9084GT-M12X-BP2-MV



















































































































































































Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды

ORiNG TRGPS-9084GT-M12X-BP2-MV, Руководство пользователя

Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды