ORiNG TRGPS-9084GT-M12X-BP2-MV Скачать руководство пользователя страница 110

Страница: 110 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

109

specific source MAC address. The legal format is

"xx-xx-xx-xx-xx-xx". Frames matching the ACE will use this SMAC

value.

DMAC Filter

Specifies the destination MAC filter for this ACE

Any

: no DMAC filter is specified (DMAC filter status is "

don't-care

").

: frame must be multicast.

: frame must be broadcast.

: frame must be unicast.

Specific

: If you want to filter a specific destination MAC address with

the ACE, choose this value. A field for entering a DMAC value

appears.

DMAC Value

When

Specific

is selected for the DMAC filter, you can enter a

specific

destination MAC address. The legal format is

"xx-xx-xx-xx-xx-xx". Frames matching the ACE will use this DMAC

value.

Label

Description

VLAN ID Filter

Specifies the VLAN ID filter for the ACE

Any

: no VLAN ID filter is specified (VLAN ID filter status is

don't-care

").

Specific

: if you want to filter a specific VLAN ID with the ACE,

choose this value. A field for entering a VLAN ID number appears.

VLAN ID

When

Specific

is selected for the VLAN ID filter, you can enter a

specific VLAN ID number. The allowed range is 1 to 4095. Frames

matching the ACE will use this VLAN ID value.

Tag Priority

Specifies the tag priority for the ACE. A frame matching the ACE will

use this tag priority. The allowed number range is 0 to 7.

Any

means

that no tag priority is specified (tag priority is "

don't-care

").

Содержание TRGPS-9084GT-M12X-BP2-MV



















































































































































































Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды

ORiNG TRGPS-9084GT-M12X-BP2-MV, Руководство пользователя

Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды