ORiNG IPS-3082GC-AT Скачать руководство пользователя страница 107

Страница: 107 / 120

IPS-3082GC-AT

User’s Manual

ORing Industrial Networking Corp

106

does not receive a

bridge protocol data

unit (BPDU) message

from the root switch

within this interval, it

recomputed the

Spanning Tree

Protocol (STP)

topology.

spanning-tree

hello-time

[seconds]

Use the spanning-tree

hello-time global

configuration

command to specify

the interval between

hello bridge protocol

data units (BPDUs).

switch(config)#spanning-tree

hello-time 3

spanning-tree

forward-time

[seconds]

Use the spanning-tree

forward-time global

configuration

command to set the

forwarding-time for the

specified

spanning-tree

instances. The

forwarding time

determines how long

each of the listening

and

learning states last

before the port begins

forwarding.

switch(config)# spanning-tree

forward-time 20

stp-path-cost

[1to200000000]

Use the spanning-tree

cost interface

configuration

command to set the

path cost for Spanning

Tree

switch(config)#interface fastEthernet

switch(config-if)#stp-path-cost 20

Содержание IPS-3082GC-AT

























































































































Результаты поиска

Содержание IPS-3082GC-AT

Отзывы:

Бренды по названию

Популярные бренды

ORiNG IPS-3082GC-AT, Руководство пользователя

Результаты поиска

Содержание IPS-3082GC-AT

Отзывы:

Бренды по названию

Популярные бренды