ORiNG IPS-3082GC-AT Скачать руководство пользователя страница 104

Страница: 104 / 120

IPS-3082GC-AT

User’s Manual

ORing Industrial Networking Corp

103

switch(config-if)#show interface

accounting

no accounting

Clear interface

accounting

information

switch(config)#interface

fastEthernet 2

switch(config-if)#no accounting

6.4 Commands Set List

—Trunk command set

IPS-3082GC-AT

Commands

Level Description

Example

aggregator priority

[1to65535]

Set port group system

priority

switch(config)#aggregator priority 22

aggregator activityport

[Port Numbers]

Set activity port

switch(config)#aggregator

activityport 2

aggregator group

[GroupID] [Port-list]

lacp

workp

[Workport]

Assign a trunk group

with LACP active.

[GroupID] :1to3

[Port-list]:Member port

list, This parameter

could be a port

range(ex.1-4) or a port

list separate by a

comma(ex.2, 3, 6)

[Workport]: The

amount of work ports,

this value could not be

less than zero or be

large than the amount

of member ports.

switch(config)#aggregator group 1

1-4 lacp workp 2

switch(config)#aggregator group 2

1,4,3 lacp workp 3

aggregator group

[GroupID] [Port-list]

nolacp

Assign a static trunk

group.

[GroupID] :1to3

[Port-list]:Member port

list, This parameter

could be a port

range(ex.1-4) or a port

list separate by a

switch(config)#aggregator group 1

2-4 nolacp

switch(config)#aggreator group 1

3,1,2 nolacp

Содержание IPS-3082GC-AT

























































































































Результаты поиска

Содержание IPS-3082GC-AT

Отзывы:

Бренды по названию

Популярные бренды

ORiNG IPS-3082GC-AT, Руководство пользователя

Результаты поиска

Содержание IPS-3082GC-AT

Отзывы:

Бренды по названию

Популярные бренды