ORiNG IAP-W420 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 41

ORiNG IAP-W420 Скачать руководство пользователя страница 26

IAP-W420/W422 UserManual

ORingIndustrial Networking Corp

25

set as the Wireless Network. If no Interface is selected, all

interfaces would be within the LAN zone.

Firewall Setting

Label

Description

Create/Assign

firewall-zone

This field chooses the firewall zone you want to assign to this

interface. Select

unspecified

to remove the interface from the

associated zone or fill out the

create

field to define a new zone and

attach the interface to it.

The default is set to

lan

.

DHCP Server

The Dynamic Host Configuration Protocol (DHCP) is a standardized networking protocol

used by servers on an IP network to allocate IP addresses automatically to client devices.It is

recommended to enable the DHCP server because network address translation (NAT)

occurs between the WAN zone and the LAN zone. Devices or computers that connect to this

hotspot router can then obtain their IP addresses automatically. In addition, the default

gateway IP address and the DNS server IP address are automatically configured for these

connected devices.If the DHCP server is left disabled, it is still possible for devices to

connect to the hotspot. Each device would need a unique static IP address on the same

subnet as this hotspot router. Set the default gateway and DNS server for the device both to

be the IP address of this hotspot router.

General Setup

Label

Description

Ignore interface

Disables DHCP for this interface. You should uncheck this to

enable DHCP.

Start

Specifies the lowest leased address as offset from the network

«
...
24
25
26
27
28
...
»

Содержание IAP-W420










































Отзывы:

Нет отзывов