manualshive.com logo in svg

Origio BT37, Руководство пользователя, Страница: 5 / 80

Поделиться
Скачать
Origio BT37 Скачать руководство пользователя страница 5

5

1.2  Notices

Product names and designations that are referred to in this document may be either trademarks and/

or registered trademarks and are recognised as the property of their respective owners.

This information is provided without warranty, express or implied, and including but not limited to any 

implied warranties in respect of merchantability or fitness for any purpose, except to the extent that 

such provisions are held to be void, in violation of applicable law or unenforceable in a specific  juris-

diction.

Planer plc reserves the right to alter products and their specifications without notice.

© 2016 Planer plc

1.3  Indications for use

The Planer BT37 Incubator is intended to be used to provide an environment with controlled temper-

ature at or near body temperature, CO₂, O₂ and N₂ gases, and elevated humidity for the development 

of gametes and embryos during in vitro fertilization (IVF) / assisted reproductive technology (ART) 

treatments.

1.4  Symbols in the manual

Safety information. Failure to follow these instructions may result in personal 

or third-party injury.

Important information. Failure to follow these instructions may result in 

damage to equipment, samples or data.

Hints.

Содержание BT37

















































































Отзывы:

Нет отзывов