Original inside NOVACAT 8600 Скачать руководство пользователя страница 6

Страница: 6 / 69

- 6 -

0700_GB-ANBAU_384

ATTACHING TO TRACTOR

Centre-mount (M) mower unit to tractor

- Adjust lower link accordingly.

- Secure the lower hydraulic link so that the appliance

cannot swing sideways.

Frame in horizontal position

- Bring frame into horizontal position by adjusting linkage

arm spindle (15).

Setting lower link height

- Adjust tractor's hydraulics (ST) using bottom stop.

- The drive shaft (GW) should be about horizontal

when mowing.

This height allows optimal evenness when working on
uneven ground and need not be changed for swinging
cutter bar up.

TD 79/98/01

Attaching implement to tractor

Safety hints:

see supplement-

A1 points 7.), 8a.

- 8h.)

Setting upper link height using spindle

- By turning upper link spindle (16) the cutting height is

adjusted.

A hydraulic upper link is recommended.

(double-action hydraulic connection)

Safety hints

This appliance is

designed only

for use with

tractors (not

for automotive

machines).

In the case of

automotive

machines, the

driver´s visual

range is restricted

when the two

outer mower

bars are raised

in the transport

position.

Содержание NOVACAT 8600






































































Результаты поиска

Содержание NOVACAT 8600

Отзывы:

Бренды по названию

Популярные бренды

Original inside NOVACAT 8600, Руководство оператора

Результаты поиска

Содержание NOVACAT 8600

Отзывы:

Бренды по названию

Популярные бренды