5
To Operate
Make sure the disposable paper filter dust bag is in place.
DO NOT
operate the cleaner without a paper filter dust bag.
Plug the power cord into an electrical outlet.
Press the ON(l) - OFF(O) switch on handle assembly when
ready to operate.
General Information
The performance of your new cleaner greatly depends upon
care and maintenance. The instructions in this manual will
guide you in performing basic care and maintenance. To
obtain the most satisfying years of service, read the
instructions and keep them handy for future reference.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest,
fastest, and strongest units in its class. You’ll love the way it
cleans, gets under things, and it’s SO lightweight and easy to
use.
The following are a few simple suggestions regarding its
operation:
1. When inserting a new disposable paper filter dust bag—
FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or
makes an unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and
other small objects, it is recommended that these be
removed from the floor before you vacuum. Failure to do
so may result in permanent damage to the motor suction
fan and its housing.
5.
WARNING:
Do not use your vacuum cleaner on damp
or wet surfaces. This will cause damage to the vacuum
cleaner and is dangerous to the user. Damage caused by
use on wet or damp surfaces is not covered under
warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a
month—even if it is not full! The collected dust in the dust
bag can cause odor, attract moisture, act as a breeding
area and can affect the efficiency of the cleaner.
8.
Do not run the vacuum cleaner over cord. The
revolving brush could damage the cord.
9. Use caution when vacuuming over area rug edges and
fringe.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role
in the efficiency of your ORECK vacuum cleaner. The purpose
of the paper bag is to trap dirt, but at the same time it must
be porous enough to allow air to pass through. If the paper
bag becomes clogged, no air can pass through the cleaner
and cleaning cannot take place, regardless of the cleaner’s
power.
To keep your cleaner operating at maximum efficiency,
change the dust bag frequently. DO NOT FILL ABOVE THE
LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is in proper
position, over the lower lip and the top lip of the connector.
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be
used with the ORECK cleaner. Using bags other
than genuine ORECK disposable bags will affect
the cleaning ability of your cleaner and could
cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective
operation of the cleaner. If the belt becomes stretched or cut,
it will cause the revolving brush to stop completely or slow
down. See instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your
cleaner. When buying replacement belts, use ONLY
ORECK genuine belts. Belts other than ORECK belts
will not operate the revolving brush correctly and
may create undue stress which will cause damage
to the motor and brush bearings. Using belts other
than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated
and sealed. Further lubrication is not required.
General Cleaner Care
At least once a month, check revolving brush for excessive
lint, string or hair. Remove this material.
Wipe the inside and outside
of the outer vinyl bag and the
outside of the cleaner with a
damp cloth. Also clean the
connector deflector assembly
area, base of cleaner and fan
housing area. If there is dust
in the outer bag, vacuum it or
shake it out.
A little preventative maintenance
will keep your cleaner looking
new and will ensure continued
cleaning effectiveness.
Cord Strain Relief
The cord strain relief located on the upper section of the handle
is designed to reduce stress on the cord at the base of the
handle.
Should the power cord come
loose from the cord strain
relief, it can be easily
reattached.
To attach the power cord to
the cord strain relief, grasp the
power cord approximately 12
inches from the base of the
handle. Pinch power cord
together and slide approxi-
mately 1-2 inches through the
bottom hole in flat side of cord
strain relief. Carefully slide
power cord loop over clamp
on cord strain relief and pull
excess until the power cord is tightly rested under clamp.
Operating Instructions
Cord Strain
Relief
Clamp
