background image

 

  Do not open the fuel cap while running the engine.  

  W hen  refueling,  be  sure   to  stop  the  engine  and  allow  it  to  cool  down.  There  is  a  danger  of 

suffering burns. 

  W hen  refueling,  be  sure  not  to  fill  the  fuel  tank  over  the  maximum  level.  If  you  do  overfill  the 

fuel  tank,  remove  fuel  until  it  sits  below  the  maximum  level.  Over -fueling  can  cause  fire  and 

other accidents. 

  After  refueling,  securely  close  the  fuel  cap  and  store  the  machine  in  a  safe  place  with  no 

sources of ignition. There is a danger of fire.  

  If  you  spill  gasoline,  move  the  machine  a  safe  distance  away  without  starting  th e  engine. 

Starting the machine in close proximity to  a fuel spill  can result in a fire or other accident. Use 

a waste cloth to wipe away the spill and dispose the cloth in a suitable manner.  

  Be sure to change your clothes immediately if they come into cont act with gasoline. There is a 

danger that any gasoline on your clothes could ignite or cause you to feel unwell.  

  Do  not  refuel  in  places  such  as  inside  a  car  or  on  a  truck,  they  could  move  unexpectedly. 

Refuel  after  placing  your  fuel  container  safely  on  th e  ground,  away  from  vehicles.  Fuel  spills 

can cause fire and other accidents.   

  W hen  refueling  from  a  truck  or  trailer,  remove  gas -powered  refueling  equipment  from  the 

vehicle and refuel the machine on the ground. If this is not possible, refuel the machine  with a 

portable container rather than from a ga soline dispenser nozzle. Fuel spills can cause fire and 

other accidents.   

  Do  not  remove  the  refueling  nozzle  from  the  fuel  tank  until  you  have  finished  refueling.  Fuel 

spills can cause fire and other accident s. 

 

 

Caution when starting the engine 

 

  Do  not  modify  the  engine  as  this  can   cause  accidents  or  explosions.   Altering  this  machine  in 

any  way  will  void  the  warranty.  Orec  America  Inc.  will  bear  no  responsibility  for  damage  or 

injury caused by alterations or  modifications. 

  Do not try to alter the position of the engine governor or change the set rotation speeds.  

  Do  not  run  the  engine  in  a  place  that  is  po orly  ventilated.  Engine  exhaust   is  odorless  and 

contains carbon monoxide which can cause death or serious  injury.   

 

 

  Do not allow highly flammable su bstances near the  engine or in the path of the exhaust  as this 

can cause a fire. 

  Do  not  touch  the  engine  or  muffler  as  they  become  extremely  hot  during  operation  and  can 

cause severe burns.  

  Do not allow  weeds and leaves to accumulate in the engine, especially in the recoi l cover, air 

filter, and near the muffler. Overheating and fire  can result. 

  Ensure that the drive clutch and blade clutch are in the [OFF] position, the  speed change lever 

is in the [N] position,  and the brake is ON, before starting the engine . Taking precautions when 

starting the engine can  avoid injury and accidents.   

  After starting the engine with the blade clutch and drive clutch in the [OFF] position, check the 

V-belt  to  be  absolutely  certain   that  it  is  not  moving.  If  the  V -belt  is  moving  even  a  little, 

immediately  switch  off  the  engine  and  adjust  the  belt  guard  and  the  wire.  Not  taking 

precautions can avoid injury and accidents.  

 

 

Содержание AHRC 663
















































Отзывы: