background image

 

25 

  Oiled Parts Inspection, Replacement, and Lubrication   

 

 This  machine  is  shipped  WITH 

GEAR  OIL.  However,  please  check  if  it’s  lubricated  with  the 

described  oil,  in  the  described  parts,  and  in  the  described  quantities  before  use.   Low  oil  level 

can cause machine damage. This type of damage is not covered by manufacture warranty.  

 To always operate this machine in good condition, perform oil changes  as recommended. 

 When  performing  inspection,  replacement,  or  lubrication  of  oiled  parts,  place  the  machine  on  a 

flat,  open  surface.  Switch  on  the  engine  and  warm  it  up  to  confirm  it  is  working  properly.  Then 

switch off the engine, allow it to cool down and remove the spark plug cord.  

After switching off, please wait at least  5 minutes for all parts to cool down before   you touch the 

machine.  Immediately  after  the  engine  has  stopped,  the  body  will  be  very  hot  and  can  cause 

burns if touched.   

 After switching off the engine, oil will still be in the engine and  transmission so the quantity of oil 

remaining will not be exactly displayed. 

 After changing the oil, please dispose of waste oil  in accordance with local laws and regulations . 

 

Transmission oil lubrication, inspection, and replacement 

 

Inspection 

Remove the oil inlet plug from the upper part of the  transmission case on 

the left side of the transmission, and check oil. 

Check that the oil is fill to the inlet opening, if so, the oil is at the correct 

level. 

 

 

 

Replacement/Lubrication 

Prepare a suitable container for removed oil. Replace oil after the first 

20 

hours

  of  operation  and  roughly  every  100  hours  thereafter  by  removing 

the drain plug from the bottom left side of the  transmission case. 

After  reattaching  the  drain plug, fill  with  1.7  US  qt  (1.6L)  of transmission 

oil (SAE 90 or SAE 80W -90) by pouring through the oil inlet. 

 

 

 

 

 

 

  After putting in oil, be sure to properly reattach the oil inlet plug to avoid any leakages.  

 Make sure the drain plug gasket contacts the mounting surface and then  turn it 3/4 of a rotation. 

 

 

 

Oil inlet plug 

Drain plug 

Содержание AHRC 663
















































Отзывы: