manualshive.com logo in svg

ORBCOMM ST 9100, Руководство по установке

Поделиться
Скачать
ORBCOMM ST 9100 Скачать руководство пользователя страница 19

ST 9100 - INSTALLATION GUIDE

7. Use the provided cable ties to secure the antenna to the asset.

Note:

If the large clearance hole required for the right-angle SMA cable connector is considered too large,
there is the option to use a smaller clearance hole in the mounting surface and install the cable
from inside the asset after the antenna has been tied down.

In this case, first confirm there is enough room from inside the asset to thread the SMA cable
connector by hand and clearance for the wrench to apply the final torque.

CAUTION:  Cable management and connector strain relief must be incorporated in the installation. Secure the

cable no more than 15 cm (6 in.) from the antenna enclosure and at regular intervals along its
length as part of the installation to prevent cable wear and eliminate strain on the transceiver
connector. Damage to the transceiver connector interface or cable might result in hardware failure.

1.4.3 Cellular Antenna

1. Clean the antenna mounting surface with isopropyl alcohol to remove any dirt or grime. Make sure the surface

is dry before applying the antenna’s adhesive strip.

2. Remove the adhesive strip from the cellular antenna.

3. Mount the cellular antenna on the inside of the window.

Figure 10

shows mounting examples on an

automobile.

Figure 10: Sample Cellular Mounting Locations – automobile example

4. Secure the cellular antenna cable in place.

1.5 Route the Main Cable

Consider the following guidelines before routing the cable assembly.

CAUTION:  Ensure the power cable is not pinched, kinked or worn down by any objects or moving parts such

as the door hinges. It is very important to secure the cable at many points along its path.

CAUTION:  Prior to working on any cabling, ensure that the transceiver is powered off and unable to start while

work is in progress.

l

Do not route the cable near the engine if routing through the engine compartment. This location subjects the
cable to extreme heat.

l

Keep the cable away from hot surfaces such as exhaust pipes because this may damage the cable.

T414, Version 0.04 BETA

© ORBCOMM

®

Proprietary

19

Содержание ST 9100







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды