background image

8

OPERATING INSTRUCTIONS

Orascoptic

®

 Telescopes

Telescope Prescription Service 

When your eyes change, you can send your telescopes into our optical laboratory to install your 
new prescription.  Package your telescopes and prescription carefully.  In the U.S. call technical 
Support (see back of manual) to make arrangements.  Ship them to the address on the back 
of this manual.  Outside the U.S. call your Orascoptic distributor to arrange for lens change 
service. DO NOT SHIP BEFORE CALLING TO MAKE ARRANGEMENTS.  

When coordinating the return of your telescope, please allow sufficient time for the installation 
of your prescription.  If you are sending in a through-the-lens telescope, your new prescription 
needs to be installed in both the eyeglass lens and inside the telescopes. Please discuss your 
schedule with Technical Support or your distributor to coordinate the return shipment of your 
telescopes.

If you ever need a prescription change to your Revolution Rx Insert, there is no need to send 
in your loupes for maintenance.  For a nominal price, Orascoptic will make you a new insert to 
accommodate your new prescription.

Cleaning Instructions

Your telescopes are manufactured from the highest quality components and will provide you 
with a long, useful life, with proper care.  These are precision optical instruments that must be 
properly cleaned and protected from rough use and improper storage.  To avoid scratching the 
telescope lenses, rinse the telescopes and frame under fast-running water to remove gross 
debris. DO NOT SUBMERGE IN ANY LIQUID OR AN ULTRASONIC CLEANER OR DAMAGE 
MAY RESULT.

You may disinfect using either a quaternary ammonium disinfectant such as CaviCide

®

, or a 

phenol alcohol-based spray such as Lysol

®

  brand disinfectant.  Follow the label directions.  

DO NOT USE AN AUTOCLAVE, CHEMICLAVE, GLUTARALDEHYDE, IODOPHOR OR ANY 
OTHER STERILIZATION METHOD, OR DAMAGE MAY RESULT.  If there are any questions, 
please call Customer Service at the toll-free number on the back of this manual.

Finally, clean all lens surfaces with an optical lens cleaning cloth that is formulated for use with 
coated lens surfaces.  These cleaning cloths can be purchased at major retail chains, optical 
stores and drug stores.  

Using Your Orascoptic Telescopes

Depending on the magnification level of your telescopes you could experience some 
disorientation.  This is normal.  Some professionals begin to use the telescopes full-time and 
some require a breaking-in period. 

If you experience difficulty, gradually increase the length of daily use.  Generally a break-in 
period lasts no more than two to three weeks.  Call Technical Support if you need assistance.  
See back of manual. 

Содержание Telescopes












Отзывы: