Oracle X7-2 Скачать руководство пользователя страница 83

Страница: 83 / 148

Using Oracle ILOM

The Oracle Server X7-2 and Oracle Server X7-2L are shipped with the latest version of Oracle

Integrated Lights Out Manager (ILOM). Oracle ILOM is system management firmware

embedded on the service processor (SP). It provides extensive management and monitoring

capabilities for the server.

This section describes how to access and get started using Oracle ILOM for your server.

■

“Connecting to Oracle ILOM” on page 83

■

“Oracle ILOM Hardware and Interfaces” on page 84

■

“Accessing Oracle ILOM” on page 84

■

“Modifying Network Settings” on page 88

■

“Redirecting the Host Console Using Oracle ILOM” on page 92

■

“Troubleshooting Oracle ILOM” on page 131

Related Information

■

“Installation Procedure Overview” on page 11

■

“Connecting Cables and Applying Power” on page 71

Connecting to Oracle ILOM

You can connect to Oracle ILOM using one of these methods:

■

Direct connection to SER MGT port (CLI only)

– For information, see

“Log In to Oracle

ILOM Using a Local Serial Connection” on page 85

■

Dedicated remote network management connection –

For information, see

“Log In to

Oracle ILOM Using a Remote Ethernet Connection” on page 86

■

Remote sideband management connnection –

For information, refer to Sideband Network

Management Connection in the

Oracle ILOM Administrator's Guide for Configuration and

Maintenance, Firmware Release 4.0.x

http://www.oracle.com/goto/ilom/docs

Using Oracle ILOM

Содержание X7-2





















































































































































Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды

Oracle X7-2, Руководство по установке

Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды