Oracle Sun Server X4-4 Скачать руководство пользователя страница 79

Страница: 79 / 148

Configure Server Drives for OS Installation

This section describes how to configure a server boot disk for operating system installation and

configure RAID.

Description

Links

Learn about storage drive configuration options.

Supported options depend on your server's host bus

adapter (HBA), requirements for RAID, and whether or

not you have a preinstalled OS.

“Drive Configuration Options” on page 79

Configure server storage drives into RAID volumes

using Oracle System Assistant.

“Configuring RAID Using Oracle System

Assistant” on page 81

Configure server storage drives into RAID volumes

using the BIOS RAID configuration utilities.

“Configuring RAID Using the BIOS RAID

Configuration Utilities” on page 93

Learn about the operating system installation and update

tasks.

“Set Up an Operating System and

Drivers” on page 104

Drive Configuration Options

Preparing a system drive to be a boot device for an operating system (OS) is a critical step in

the server set up process. The procedures used to configure RAID depend on which supported

SAS HBA is installed in the server and which server BIOS boot mode is selected (UEFI or

Legacy, see

“UEFI BIOS” on page 24

for details). You can use either Oracle System Assistant

(recommended) or BIOS/option ROM-based RAID configuration utilities to configure RAID.

Once you have installed your operating system, supported OS-based RAID management

utilities included with your server can be used to manage RAID storage drives.

Choose an option for configuring your server storage drives:

■

Option 1

- If you have purchased an optional factory preinstalled OS or virtual machine

software image, a boot drive containing the image has already been created for you. You

cannot configure the disk with the preinstalled OS image as a RAID volume because that

Configure Server Drives for OS Installation

Содержание Sun Server X4-4





















































































































































Результаты поиска

Содержание Sun Server X4-4

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Server X4-4, Руководство по установке

Результаты поиска

Содержание Sun Server X4-4

Отзывы:

Бренды по названию

Популярные бренды