Oracle Sun Server X4-4 Скачать руководство пользователя страница 93

Страница: 93 / 148

Configuring RAID Using the BIOS RAID Configuration Utilities

Configuring RAID Using the BIOS RAID Configuration

Utilities

If Oracle System Assistant is not available, you can use the BIOS RAID configuration utilities

that reside in the HBA firmware. The procedures for configuring RAID differ depending on the

type of HBA installed the server.

For instructions on how to use these utilities, see the following sections:

■

“Configuring RAID Using the BIOS With the Sun Storage 6 Gb SAS PCIe Internal

HBA” on page 93

■

“Configuring RAID Using the BIOS With the Sun Storage 6 Gb SAS PCIe RAID Internal

HBA” on page 96

See Also

■

“Drive Configuration Options” on page 79

■

“Configuring RAID Using Oracle System Assistant” on page 81

Configuring RAID Using the BIOS With the Sun

Storage 6 Gb SAS PCIe Internal HBA

The BIOS RAID configuration utilities support configuring RAID with the server set to UEFI

BIOS Boot Mode or Legacy BIOS Boot Mode. A separate utility is provided for each boot

mode.

Note -

Some operating systems and virtual machine software only support the Legacy BIOS

Boot Mode. For a list of operating systems that support UEFI BIOS Boot Mode, see

“UEFI

BIOS” on page 24

■

“Configure RAID in UEFI BIOS Boot Mode” on page 93

■

“Configure RAID in Legacy BIOS Boot Mode” on page 95

Configure RAID in UEFI BIOS Boot Mode

Power on or reset the server.

For example, to reset the server:

Configure Server Drives for OS Installation

Содержание Sun Server X4-4





















































































































































Результаты поиска

Содержание Sun Server X4-4

Отзывы:

Oracle Sun Server X4-4, Руководство по установке, Страница: 93 / 148

Результаты поиска

Содержание Sun Server X4-4

Отзывы: