Oracle Sun Netra X4270 Скачать руководство пользователя страница 32

Страница: 32 / 238

Inspecting the System

Check for version dependencies, especially with third-party software.

Related Information

■

“Gather Service Information” on page 31

■

“Inspecting the System” on page 32

Inspecting the System

Controls that have been improperly set and cables that are loose or improperly connected are

common causes of problems with hardware components. Follow these tasks to locate common

problems with the system.

■

“Troubleshoot Power Problems” on page 32

■

“Inspect the Server Externally” on page 33

■

“Inspect Internal Server Components” on page 33

Related Information

■

“Understanding the Server” on page 13

■

“Preparing for Service” on page 73

■

“Preparing for Service” on page 73

Troubleshoot Power Problems

If the system is powered off, power on the server.

See

“Power On the Server” on page 214

■

If the server powers on, go to

“Inspect the Server Externally” on page 33

■

If the server does not power on, go to

Step 2

Check that AC or DC power cords are attached firmly to the server???s power

supplies and to the AC or DC sources.

Related Information

■

“Power On the Server” on page 214

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды