Oracle Sun Netra X4270 Скачать руководство пользователя страница 73

Страница: 73 / 238

Preparing for Service

These topics describe the safety considerations and provides prerequisite procedures and

information to replace components within the server.

■

“Safety Precautions” on page 73

■

“Safety Symbols” on page 74

■

“Electrostatic Discharge Safety” on page 74

■

“Required Tools” on page 75

■

“Preparing the Server for Component Replacement” on page 75

Related Information

■

“Returning Server to Operation” on page 211

Safety Precautions

For your protection, observe the following safety precautions when setting up your equipment:

■

Follow all standard cautions, warnings, and instructions marked on the equipment and

described in

Important Safety Information for Sun Hardware Systems

■

Ensure that the voltage and frequency of your power source match the voltage and

frequency inscribed on the equipment???s electrical rating label.

■

Follow the electrostatic discharge safety practices as described in this section.

■

Disconnect both power supply cords before servicing.

Related Information

■

“Safety Symbols” on page 74

■

“Electrostatic Discharge Safety” on page 74

Preparing for Service

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды