Oracle SPARC T8-2 Скачать руководство пользователя | Manualshive

Страница: 73 / 188

background image

Verify a Drive

a.

Slide the drive filler into the drive slot until it is fully seated.

b.

Close the latch to lock the filler in place.

Related Information

■

“Determine Which Drive Is Faulty” on page 65

■

“Remove a Drive” on page 65

■

“Install a Drive” on page 70

■

“Remove a Drive Filler” on page 69

■

“Verify a Drive” on page 73

Verify a Drive

1.

If the OS is shut down, and the drive you replaced was not the boot device, boot

the OS.

Depending on the nature of the replaced drive, you might need to perform administrative tasks

to reinstall software before the server can boot. Refer to the Oracle Solaris OS administration

documentation for more information.

2.

At the Oracle Solaris prompt, list all drives in the device tree, including any

drives that are not configured.

#

cfgadm -al

This command helps you identify the drive you installed.

Ap_id Type        Receptacle Occupant   Condition
c0 scsi-bus    connected configured   unknown
c0::dsk/c1t0d0 disk        connected configured   unknown
c0::sd1 disk        connected unconfigured   unknown
usb0/1 unknown     empty unconfigured   ok
usb0/2 unknown     empty unconfigured   ok
...

3.

Configure the drive.

For example, to configure the second disk

c0::sd1

, type:

Servicing Drives

73

«
...
71
72
73
74
75
...
»

Содержание SPARC T8-2





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPARC T8-2

MCX-2000 - MusicCAST Digital Audio Server

Бренд: Yamaha Страницы: 25

D-811_002-NXS-SAG

Бренд: NOMACHINE Страницы: 19

SimpliVity 2600 Gen10

Бренд: HPE Страницы: 37

digitalSTROM-Server

Бренд: aizo Страницы: 2

Бренд: AIC Страницы: 88

AssuredSAN 4004 Series

Бренд: Dot Hill Страницы: 59

Бренд: d3 Technologies Страницы: 10

Бренд: Panasonic Страницы: 17

Бренд: Panasonic Страницы: 42

Бренд: Panasonic Страницы: 316

Бренд: Panasonic Страницы: 456

Turbo NAS TS-219P

Бренд: QNAP Страницы: 49

Бренд: Generac Power Systems Страницы: 52

Бренд: Alfresco Страницы: 49

Бренд: Maverick System Страницы: 58

Бренд: 7th Sense Страницы: 24

Бренд: MPC Страницы: 120

Бренд: Oracle Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды