Oracle SPARC T8-2 Скачать руководство пользователя страница 65

Страница: 65 / 188

Determine Which Drive Is Faulty

■

“Remove a Drive” on page 65

■

“Install a Drive” on page 70

■

“Remove a Drive Filler” on page 69

■

“Install a Drive Filler” on page 72

■

“Verify a Drive” on page 73

Determine Which Drive Is Faulty

The following LEDs are lit when a drive fault is detected:

■

System Service Required LEDs on the front and rear panels.

■

Service Required LED on the faulty drive.

Check to see if any System Service Required LEDs are lit or flashing.

See

“Interpreting LEDs” on page 33

From the front of the server, check the drive LEDs to identify the faulty drive.

The amber Service Required LED is lit on the drive that needs to be replaced.
See

“Drive LEDs” on page 64

Remove the faulty drive.

See

“Remove a Drive” on page 65

Related Information

■

“Drive LEDs” on page 64

■

“Remove a Drive” on page 65

■

“Install a Drive” on page 70

■

“Verify a Drive” on page 73

■

“Detecting and Managing Faults” on page 27

Remove a Drive

This is a hot-service procedure that can be performed by a customer while the server is running.

Caution -

This procedure requires that you handle components that are sensitive to ESD which

can cause server components to fail.

Servicing Drives

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Oracle SPARC T8-2, Руководство по обслуживанию, Страница: 65 / 188

Результаты поиска

Содержание SPARC T8-2

Отзывы: