Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 35 / 258

Check the Message Buffer

Description

Links

Generate and examine low-level diagnostic information

generated by POST.

“POST Overview” on page 37

“Configure POST” on page 37

“Oracle ILOM Properties That Affect POST

Behavior” on page 39

Related Information

■

“Checking for Faults” on page 25

■

“Clear a Fault Manually” on page 40

Check the Message Buffer

The

dmesg

command checks the system buffer for recent diagnostic messages and displays the

messages.

Log in as superuser.

Type:

dmesg

Related Information

■

“View Log Files (Oracle Solaris)” on page 35

■

“View Log Files (Oracle ILOM)” on page 36

■

“POST Overview” on page 37

View Log Files (Oracle Solaris)

The error logging daemon,

syslogd

, automatically records various system warnings, errors, and

faults in message files. These messages can alert you to system problems such as a device that

is about to fail.

The

/var/adm

directory contains several message files. The most recent messages are in

the /

var/adm/messages

file. After a period of time (usually every week), a new

messages

Detecting and Managing Faults

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды