Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 125 / 258

Servicing the DVD Drive

The internal DVD drive is a SATA optical-storage device with DVD DL-RW capabilities. The

DVD drive is located below the disk drives, at the front center of the server. See

“Component

Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

Description

Links

Replace the faulty DVD drive.

“Remove the DVD Drive” on page 125

“Install the DVD Drive” on page 128

Remove the DVD drive as part of another

component's service operation.

“Remove the DVD Drive” on page 125

Install the DVD drive as part of another

component's service operation.

“Install the DVD Drive” on page 128

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Remove the DVD Drive

Removing the DVD drive is a cold-plug operation. You must power off the server before you

remove the DVD drive.

Caution -

Overheating hazard. A DVD drive, even if it does not function, or a filler panel, must

be present in the DVD drive slot. Do not perform this procedure until you have a replacement

DVD drive or filler panel available.

Servicing the DVD Drive

125

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды