5
OPERATIONS
• Plug in the equipment to a power socket close to the equipment.
• On the display panel, a Red LED (J) ‘power’ and a Green blinking LED (H) comes on. The
Green LED will stop blinking when the correct temperature for sealing is reached.
• Should both RED and GREEN LEDS start blinking at the same time, replace the cutting
blade straight away.
• Then press the Start/Pause button (I) to start making bags/cushion.
• When you finish making air bags/cushion, press the Start/Pause button again, the
equipment will stop immediately. There is a perforated line on the foil between each
bag/cushion, tear off required length needed. Air pressure varies between bag/cush
ion sizes to meet different packaging requirements, use the pressure control knob (G)
to set the pressure to suit your needs and get the best bag/cushion results. Too much
air will course jamming or not enough air in the bags/cushions could course a jam
and damage to goods. Area ‘’A’’ as seen in (Dig: 9) on the next page, is suggested for
200mm wide bags/cushions and area “B” is suggested for 400mm wide bags/cushions.
• If you press the Start/Pause button to stop making bags/cushions when the tempera
ture is correct and the Green LED is not blinking for more than 30 seconds it may cause
the foil to melt and make a small hole, this is a normal situation and will not af
fect air bag/cushion, you can tear off and release foil from hot roller to prevent more
melted holes.
8
4
INSTALLATION
Opus aeroPOUCH 8 • User guide
EN
• Plug in the power cable into the equipment at the back. See (Dig 1)
• Before you install the roll of foil bags cut the lower corner off with a pair of sharp
scissors See (Dig. 2)
• Unfold the stabilizing arm and secure. (B)
• Install the tension bars (C).
• Install the roll of foil bags onto the feeder capstan See (Dig 3) When putting the roll
foil bags onto the feeder capstan, ensure the grooves inside the inner roll/tube fit
onto the capstan grooves correctly.
• Feed the foil over the first tension bar and under the second tension bar. See (Dig 4)
• Now feed the cut corner of the foil bags onto the air nozzle tube. See (Dig 5)
• Pull the foil up to the hot sealing rollers so they can grip the foil. Hold the foil with
one hand to guide it through and then push the Start/Pause button helping the foil
to start being pulled through the sealing rollers. See (Dig 6 & 7).
3000
1. Caution
Please read carefully before use.
1.1 Remove the machine from the package box carefully.
1.2 Put the machine in the clean and flat working table,
Refer fig. A.
fig.A
2. Installation Steps
2.1 Connect the correct electrical power. Refer fig. 1.
2.2 Installation of film roll.
2.2.1 The bubble film should be cut with a scissors in the lower
right corner before loading the film, Refer 2.
2.2.2 Put the roll film on the feeding roller properly. There is a groove inside the roll film
header should align and feed into feeding roller’s protrusion part. Refer fig. 3.
2.2.3 The roll feeding direction to pass through to the tension column, Refer fig. 4.
2.2.4 Threading roll film pass through the air nozzle. Refer fig. 5.
2.2.5 Pulling the roll film to close enough and touch just right between the hot sealing
wheels to ensure when push start button the machine can pull out film till reach
the front pulling wheels, and start making air cushion smoothly. Refer fig. 6,7.
B
C
D E F
A. Feeding roller
B. Foot stand
C. Tension column
D. Heating roller
E. Puller
F. Air nozzle
G. Air density setting knob
H. Start/Pause knob indicator (green indicator)
I. Start/Pause button
J. Power indicator(red indicator)
K. SPower Switch
L. Electrical Cable
4.
Cutter replacement
Air nozzle cutter blade replacement steps
4.1 Use the screw driver to remove the fix air nozzle screws. Refer fig. 10A.
4.2 Pulling out the air nozzle. Refer fig.10B.
4.3 Remove the air nozzle fix screws. Refer fig. 11.
4.4 Renew the new cutter blade (Caution: Be care of sharp blade may cut you
fingers).
4.5 Put the air nozzle back and use the screw driver to fix tightly of the 2 fix-screws.
Refer fig. 10,11.
5.
Machine Maintenance
5.1 Unplug the power cord during maintenance.
5.2 Clean hot seals and rollers regularly. Refer fig 12.
5.3 Ensure there is no jammed film and dirt at the air
nozzle or cutter blade.
5.4 Clean the air nozzle regularly.
5.5 Replace the cutter blade when blade is not sharp.
6.
Specification
2.3 Operations
2.3.1 Connecting the electrical power, and press the power switch , Refer fig. 8.
2.3.1 After power on the machine, the power indicator red light will go on and green
light start to flashing, the machine is under heating processing (The warm up
time around 4 mins).
2.3.2 When green light is solid on that mean machine is ready to making air cushion,
then press the start / pause button to start.
2.3.3 When finish making air cushion, press the start/pause button again, machine
will stop immediately. There is a perforation line on the film to tear off the
necessary length for your requirement.
2.3.4 Air density setting: Various cushion sizes are available to meet different
packaging requirements, You can use the pressing setting knob to set up the air
density to meet you need. Please adjust the suitable air pressure to get best
air cushion performance. Too much air pressure will result jam or bad air
cushion performance (Remark: " A" area is suggest for 200mm width film and
" B" area is suggest for 400mm width film). Refer fig. 9.
2.3.5 If continuous to using the machine, press the start/pause button when machine
indicator is in solid on condition. If press stop button more than 30 seconds may
cause film melt out a small hole, it is normal situation and will not effect air cushion,
you can tear off and releace film from hot roller to prevent from melted film hole.
2.3.6 If want to power off, please make sure power indicator is in solid on condition,
tear off the film performation line ahead the air nozzle, and push start/pause
button to eject the film completely, and push the start/pause button again to
stop the machine, then you can turn off the power stwitch.
2.3.7 As for transportation requirement, please ensure the rollers without film inside
than push power button to turn off the machine while the rollers are still running.
2.4 Hibernation Function
After approximately 1.5 hours of continuly use or push the Start/Pause button and
stop machine more than half an hour, the machine will go into hibernation mode.
During hibernation, the red power indicator light will flash slowly and components
will shut off. It is recommended to give the machine a short 10-15 minute rest between
longer stretches of use.
Push the Start/Pause button to take the machine out of hiberation mode. The machine
will begin the warm-up process again. The redpower indicator will remain constant and
the green light will flash. When the greenindicator light remains constant, the machine
is again ready to use.
3. Electric Safety
3.1 Place the machine close to power socket.
3.2 Make sure the voltage meets machine’s electricity requirements.
3.3 Any extension cord used should meet the power rating of the machine.
3.4 Do not operate if the power cord is damaged.
3.5 Repair and service should be done by a qualified service technician.
Caution: Blade might blunt after a longer use, the check light green and red
will go flashing in a same time as its reminder, please check or replace the
blade every 200 rolls (300 m / roll).
11
10
12
Up
/Down
Heating
roller
G H I J K
L
Sealing speed
8m/min±10
％ (
Fix speed
)
Air density control
Adjustable (200/400mm in a different
setting and operation range)
Film roll size
200x80mm
、
200x100mm
、
200x130mm
200x150mm
、
200x200mm
400x250mm
、
400x290mm
Max. Film roll length
(W: Film width)
(L: Film length)
W
L
W
L
200mm ≤600M
400mm ≤500M
Power voltage
100-240V
50/60Hz
Poewr rate
120W
Machine size
465×225×355(mm)
Machine weight
6.5kg
3000
1. Caution
Please read carefully before use.
1.1 Remove the machine from the package box carefully.
1.2 Put the machine in the clean and flat working table,
Refer fig. A.
fig.A
2. Installation Steps
2.1 Connect the correct electrical power. Refer fig. 1.
2.2 Installation of film roll.
2.2.1 The bubble film should be cut with a scissors in the lower
right corner before loading the film, Refer 2.
2.2.2 Put the roll film on the feeding roller properly. There is a groove inside the roll film
header should align and feed into feeding roller’s protrusion part. Refer fig. 3.
2.2.3 The roll feeding direction to pass through to the tension column, Refer fig. 4.
2.2.4 Threading roll film pass through the air nozzle. Refer fig. 5.
2.2.5 Pulling the roll film to close enough and touch just right between the hot sealing
wheels to ensure when push start button the machine can pull out film till reach
the front pulling wheels, and start making air cushion smoothly. Refer fig. 6,7.
B
C
D E F
A. Feeding roller
B. Foot stand
C. Tension column
D. Heating roller
E. Puller
F. Air nozzle
G. Air density setting knob
H. Start/Pause knob indicator (green indicator)
I. Start/Pause button
J. Power indicator(red indicator)
K. SPower Switch
L. Electrical Cable
4.
Cutter replacement
Air nozzle cutter blade replacement steps
4.1 Use the screw driver to remove the fix air nozzle screws. Refer fig. 10A.
4.2 Pulling out the air nozzle. Refer fig.10B.
4.3 Remove the air nozzle fix screws. Refer fig. 11.
4.4 Renew the new cutter blade (Caution: Be care of sharp blade may cut you
fingers).
4.5 Put the air nozzle back and use the screw driver to fix tightly of the 2 fix-screws.
Refer fig. 10,11.
5.
Machine Maintenance
5.1 Unplug the power cord during maintenance.
5.2 Clean hot seals and rollers regularly. Refer fig 12.
5.3 Ensure there is no jammed film and dirt at the air
nozzle or cutter blade.
5.4 Clean the air nozzle regularly.
5.5 Replace the cutter blade when blade is not sharp.
6.
Specification
2.3 Operations
2.3.1 Connecting the electrical power, and press the power switch , Refer fig. 8.
2.3.1 After power on the machine, the power indicator red light will go on and green
light start to flashing, the machine is under heating processing (The warm up
time around 4 mins).
2.3.2 When green light is solid on that mean machine is ready to making air cushion,
then press the start / pause button to start.
2.3.3 When finish making air cushion, press the start/pause button again, machine
will stop immediately. There is a perforation line on the film to tear off the
necessary length for your requirement.
2.3.4 Air density setting: Various cushion sizes are available to meet different
packaging requirements, You can use the pressing setting knob to set up the air
density to meet you need. Please adjust the suitable air pressure to get best
air cushion performance. Too much air pressure will result jam or bad air
cushion performance (Remark: " A" area is suggest for 200mm width film and
" B" area is suggest for 400mm width film). Refer fig. 9.
2.3.5 If continuous to using the machine, press the start/pause button when machine
indicator is in solid on condition. If press stop button more than 30 seconds may
cause film melt out a small hole, it is normal situation and will not effect air cushion,
you can tear off and releace film from hot roller to prevent from melted film hole.
2.3.6 If want to power off, please make sure power indicator is in solid on condition,
tear off the film performation line ahead the air nozzle, and push start/pause
button to eject the film completely, and push the start/pause button again to
stop the machine, then you can turn off the power stwitch.
2.3.7 As for transportation requirement, please ensure the rollers without film inside
than push power button to turn off the machine while the rollers are still running.
2.4 Hibernation Function
After approximately 1.5 hours of continuly use or push the Start/Pause button and
stop machine more than half an hour, the machine will go into hibernation mode.
During hibernation, the red power indicator light will flash slowly and components
will shut off. It is recommended to give the machine a short 10-15 minute rest between
longer stretches of use.
Push the Start/Pause button to take the machine out of hiberation mode. The machine
will begin the warm-up process again. The redpower indicator will remain constant and
the green light will flash. When the greenindicator light remains constant, the machine
is again ready to use.
3. Electric Safety
3.1 Place the machine close to power socket.
3.2 Make sure the voltage meets machine’s electricity requirements.
3.3 Any extension cord used should meet the power rating of the machine.
3.4 Do not operate if the power cord is damaged.
3.5 Repair and service should be done by a qualified service technician.
Caution: Blade might blunt after a longer use, the check light green and red
will go flashing in a same time as its reminder, please check or replace the
blade every 200 rolls (300 m / roll).
11
10
12
Up
/Down
Heating
roller
G H I J K
L
Sealing speed
8m/min±10
％ (
Fix speed
)
Air density control
Adjustable (200/400mm in a different
setting and operation range)
Film roll size
200x80mm
、
200x100mm
、
200x130mm
200x150mm
、
200x200mm
400x250mm
、
400x290mm
Max. Film roll length
(W: Film width)
(L: Film length)
W
L
W
L
200mm ≤600M
400mm ≤500M
Power voltage
100-240V
50/60Hz
Poewr rate
120W
Machine size
465×225×355(mm)
Machine weight
6.5kg
3000
1. Caution
Please read carefully before use.
1.1 Remove the machine from the package box carefully.
1.2 Put the machine in the clean and flat working table,
Refer fig. A.
fig.A
2. Installation Steps
2.1 Connect the correct electrical power. Refer fig. 1.
2.2 Installation of film roll.
2.2.1 The bubble film should be cut with a scissors in the lower
right corner before loading the film, Refer 2.
2.2.2 Put the roll film on the feeding roller properly. There is a groove inside the roll film
header should align and feed into feeding roller’s protrusion part. Refer fig. 3.
2.2.3 The roll feeding direction to pass through to the tension column, Refer fig. 4.
2.2.4 Threading roll film pass through the air nozzle. Refer fig. 5.
2.2.5 Pulling the roll film to close enough and touch just right between the hot sealing
wheels to ensure when push start button the machine can pull out film till reach
the front pulling wheels, and start making air cushion smoothly. Refer fig. 6,7.
B
C
D E F
A. Feeding roller
B. Foot stand
C. Tension column
D. Heating roller
E. Puller
F. Air nozzle
G. Air density setting knob
H. Start/Pause knob indicator (green indicator)
I. Start/Pause button
J. Power indicator(red indicator)
K. SPower Switch
L. Electrical Cable
4.
Cutter replacement
Air nozzle cutter blade replacement steps
4.1 Use the screw driver to remove the fix air nozzle screws. Refer fig. 10A.
4.2 Pulling out the air nozzle. Refer fig.10B.
4.3 Remove the air nozzle fix screws. Refer fig. 11.
4.4 Renew the new cutter blade (Caution: Be care of sharp blade may cut you
fingers).
4.5 Put the air nozzle back and use the screw driver to fix tightly of the 2 fix-screws.
Refer fig. 10,11.
5.
Machine Maintenance
5.1 Unplug the power cord during maintenance.
5.2 Clean hot seals and rollers regularly. Refer fig 12.
5.3 Ensure there is no jammed film and dirt at the air
nozzle or cutter blade.
5.4 Clean the air nozzle regularly.
5.5 Replace the cutter blade when blade is not sharp.
6.
Specification
2.3 Operations
2.3.1 Connecting the electrical power, and press the power switch , Refer fig. 8.
2.3.1 After power on the machine, the power indicator red light will go on and green
light start to flashing, the machine is under heating processing (The warm up
time around 4 mins).
2.3.2 When green light is solid on that mean machine is ready to making air cushion,
then press the start / pause button to start.
2.3.3 When finish making air cushion, press the start/pause button again, machine
will stop immediately. There is a perforation line on the film to tear off the
necessary length for your requirement.
2.3.4 Air density setting: Various cushion sizes are available to meet different
packaging requirements, You can use the pressing setting knob to set up the air
density to meet you need. Please adjust the suitable air pressure to get best
air cushion performance. Too much air pressure will result jam or bad air
cushion performance (Remark: " A" area is suggest for 200mm width film and
" B" area is suggest for 400mm width film). Refer fig. 9.
2.3.5 If continuous to using the machine, press the start/pause button when machine
indicator is in solid on condition. If press stop button more than 30 seconds may
cause film melt out a small hole, it is normal situation and will not effect air cushion,
you can tear off and releace film from hot roller to prevent from melted film hole.
2.3.6 If want to power off, please make sure power indicator is in solid on condition,
tear off the film performation line ahead the air nozzle, and push start/pause
button to eject the film completely, and push the start/pause button again to
stop the machine, then you can turn off the power stwitch.
2.3.7 As for transportation requirement, please ensure the rollers without film inside
than push power button to turn off the machine while the rollers are still running.
2.4 Hibernation Function
After approximately 1.5 hours of continuly use or push the Start/Pause button and
stop machine more than half an hour, the machine will go into hibernation mode.
During hibernation, the red power indicator light will flash slowly and components
will shut off. It is recommended to give the machine a short 10-15 minute rest between
longer stretches of use.
Push the Start/Pause button to take the machine out of hiberation mode. The machine
will begin the warm-up process again. The redpower indicator will remain constant and
the green light will flash. When the greenindicator light remains constant, the machine
is again ready to use.
3. Electric Safety
3.1 Place the machine close to power socket.
3.2 Make sure the voltage meets machine’s electricity requirements.
3.3 Any extension cord used should meet the power rating of the machine.
3.4 Do not operate if the power cord is damaged.
3.5 Repair and service should be done by a qualified service technician.
Caution: Blade might blunt after a longer use, the check light green and red
will go flashing in a same time as its reminder, please check or replace the
blade every 200 rolls (300 m / roll).
11
10
12
Up
/Down
Heating
roller
G H I J K
L
Sealing speed
8m/min±10
％ (
Fix speed
)
Air density control
Adjustable (200/400mm in a different
setting and operation range)
Film roll size
200x80mm
、
200x100mm
、
200x130mm
200x150mm
、
200x200mm
400x250mm
、
400x290mm
Max. Film roll length
(W: Film width)
(L: Film length)
W
L
W
L
200mm ≤600M
400mm ≤500M
Power voltage
100-240V
50/60Hz
Poewr rate
120W
Machine size
465×225×355(mm)
Machine weight
6.5kg
