background image

 
 
 

LIMITED WARRANTY

 

 
Optimal-Vertrieb Opitz GmbH ("Opitz") warrants that this product will be free from defects in material and 
workmanship  for  a  period  of 6  months  from  the  date  of purchase  (the  "Warranty  Period").    If, during  the 
Warranty  Period,  this  product  proves  to  be  defective,  Opitz  will  remedy  the  defect  by  either  repairing  or 
replacing the product or any of its defective parts, at Opitz’s option. 
 
If you need warranty service, you must, prior to the lapse of the Warranty Period, file a claim, together with 
proof  of  purchase  and  your  original  Warranty  Certificate  received  at  the  purchase  of  the  product,  with 
Fieldworks Nursery Equipment, Grand Bay AL 36541; USA.  After a warranty claim is properly filed, Opitz 
or its designated representative will evaluate the warranty claim.  This warranty is conditioned upon your 
reasonable cooperation with Opitz in the evaluation of your warranty claim and the implementation of any 
remedy.    When  supplying  replacement  product  or  parts  under  this  warranty,  Opitz  reserves  the  right  to 
substitute product or parts of comparable value and design for any discontinued designs.  This warranty is 
not transferable and applies only to the original consumer purchaser.   
 
Opitz  does  not  assume  any  responsibility  for  failures,  breakage  or  causes  which  result  from  abuse, 
misuse,  negligence,  faulty  operation,  unauthorized  repair  or  alteration,  accident,  fire,  winds,  floods, 
moisture, other unfavorable atmospheric conditions or other causes beyond Opitz’s reasonable control or 
from failure to operate or maintain the product in accordance with the Opitz Operation Manual (a copy of 
which  is  provided  to  you  with  the  product)  or  from  normal  wear  and  tear  under  normal  usage. 

OPITZ 

EXCLUDES  AND  WILL  NOT  PAY  ANY  INCIDENTAL  AND  CONSEQUENTIAL  DAMAGES  ARISING 
OUT  OF  THE  PURCHASE  OR  USE  OF  THE  PRODUCT

.    By  this  Opitz  means  any  loss,  expense  or 

damage other than to the product itself that may result from a defect in the product.  Some states do not 
allow  the  exclusion  or  limitation  of  incidental  or  consequential  damages,  so  the  above  limitation  or 
exclusion may not apply to you. 
 

THE  DURATION  OF  ANY  IMPLIED  WARRANTIES  ARE  LIMITED  TO  THE  DURATION  OF  THE 
COVERAGE  PROVIDED  BY  THIS  LIMITED  WARRANTY  AS  INDICATED  ABOVE;  PROVIDED, 
HOWEVER,  THAT  NOTHING  IN  THIS  LIMITED  WARRANTY  SHALL  GIVE  YOU  ANY  IMPLIED 
WARRANTIES  YOU  WOULD  NOT  OTHERWISE  HAVE,  EXTEND  THE  SAME  BEYOND  THEIR 
CUSTOMARY  DURATION,  OR  MAKE  OPITZ  LIABLE  FOR  ANY  IMPLIED  WARRANTIES  THAT  IT 
WOULD NOT BE LIABLE FOR IF THIS LIMITED WARRANTY HAD NOT BEEN GIVEN.  

Some states 

do  not  allow  limitations  on  how  long  an  implied  warranty  lasts,  so  the  above  limitation  may  not  apply  to 
you. 
 
This  warranty  shall  apply  only  to  product  that  is  purchased  and  used  within  the  United  States.  This 
warranty gives you specific legal rights, and you may also have other rights that vary from state to state.  
 
 
Date of Sale:   …………………………………   Product Sold:   …………………………………………… 
 
Product Serial Number:   

…………………….   Expiration Date of the Warranty:   ……………………… 

 
Name and Address of Buyer: 

……………………………………………… 

 
 

 

 

 

……………………………………………… 

 
 

 

 

 

……………………………………………… 

 
 

 

 

 

……………………………………………… 

 
Signature of Buyer: 

 

………………………………………………. 

 

 

Содержание 1700












































Отзывы: