background image

 

SWL-1550-

M User’s Manual 

Page 10 of 11

 

 

Optilab, LLC

 

 

600 E. Camelback Road, Phoenix, AZ  85012 
Phone:  (602) 343-1496, Fax:  (602) 343-1489, Email:  [email protected] 
 

 

4.  Service and Support 

 

4.1  Warranty 

 
  

Optilab,  LLC guarantees  its  SWL-1550-M  unit  is  guaranteed  to  be 
free of defects for 1 year from the date of shipment.  The guarantee 
does not cover any damages resulting from the misuse or improper 
handling of the equipment, or any incidental or consequential loss.  
Note that the warranty will be void upon any attempt to open or to 
fix the equipment by the user without prior approval of Optilab, LLC 

 
 

4.2  Service and Calibration 

 
 

Your  SWL-1550-M  unit  has  been  designed  to  provide  years  of 
trouble-free  operation.    No  internal  maintenance  is  required 
provided that the equipment is properly handled, operated and kept 
away  from  contamination.    For  any  questions  regarding  the 
operation and performance of the unit, please contact Optilab, LLC 
at: 

 

Optilab, LLC 

 

600 E. Camelback Road 
Phoenix, AZ  85012 

 

Phone: 

(602) 343-1496

 

Fax: 

(602) 343-1489 

Email:  [email protected] 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание SWL-1550-M















Отзывы: