OPTILAB EDFA-MP-MSA Скачать руководство пользователя

Страница: 7 / 12

EDFA-MP-MSA

User’s Manual

Page 4 of 9

Optilab, LLC

600 E. Camelback Road, Phoenix, AZ 85012
Phone: (602) 343-1496, Fax: (602) 343-1489, Email: [email protected]

2.4 30 Pin-Out Diagram

Listed below is the pin-out diagram for the 30 pin port on the external of the
EDFA-MP-MSA module:

2.5 Operation Instructions

Start-up Procedure

1. Ensure that the proper cable connections are made, which includes the

cable assembly interconnects (as shown on page 4) and the 30 pin
connection between the module and power supply.

2. Plug in the After plugging in the AC/DC Power Adaptor into the appropriate

socket, the 5V VDC supply will automatically be enabled to the EDFA.

3. Ensuring the optical input signal is turned off, connect the optical signal for

amplification via the optical input port using the indicated connector
patchcords.

4. Connect the optical output port using the indicated connector patchcords to

the appropriate signal destination to utilize the amplified optical output signal.

5. After checking all physical patchcord connections, turn the input signal laser

source on.

6. The EDFA-MP-MSA is now enabled, with the gain current set to maximum

amplification for the current input signal level.

Содержание EDFA-MP-MSA












