Onkyo TX SR608, Инструкция по эксплуатации

Страница: 41 / 76

41
En
■
Speakers Type
`
Normal :
Select this if you’ve connected your front speakers
normally.
`
Bi-Amp :
Select this if you’ve bi-amped your front speakers.
Note
• Powered Zone 2 cannot be used if “ Speakers Type ” is set to
“ Bi-Amp ” (
➔
56 ).
■
Speaker Terminal Assign
Front High/Front Wide/Zone2
With this setting, you can specify the speakers con-
nected to
FRONT HIGH OR FRONT WIDE OR
ZONE 2 SPEAKERS terminals.
`
Front High :
Front high speakers can be used.
`
Front Wide :
Front wide speakers can be used.
`
Zone2 :
Zone 2 speakers can be used. (Powered Zone 2
enabled).
Note
• If the “ Speakers Type ” setting is set to “ Bi-Amp ”, or Powered
Zone 2 cannot be used.
SurrBack/Front High/Front Wide
With this setting, you can specify the speakers con-
nected to
SURR BACK OR FRONT HIGH OR
FRONT WIDE SPEAKERS terminals.
`
Surr Back :
Surround back speakers can be used.
`
Front High :
Front high speakers can be used.
`
Front Wide :
Front wide speakers can be used.
Note
• If the “ Speakers Type ” setting is set to “ Bi-Amp ”, or Powered
Zone 2 cannot be used.
• If “ Front High ” is selected in the “ Front High/Front Wide/
Zone2 ” setting, you cannot select “ Front High ” here.
• If “ Front Wide ” is selected in the “ SurrBack/Front High/
Front Wide ” setting, you cannot select “ Front Wide ” here.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band ” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey 2EQ
® Room Correction and Speaker
Setup, please make sure manually that any THX speakers
are set to “
80Hz(THX) ” crossover.
■
Subwoofer
`
Yes :
Select if a subwoofer is connected.
`
No :
Select if no subwoofer is connected.
■
Front
`
Full Band
`
40Hz to 80Hz(THX) to 100Hz , 120Hz , 150Hz ,
200Hz
Note
• If the “ Subwoofer ” setting is set to “ No ”, the “ Front ” setting is
fixed at “ Full Band ”.
■
Center *1 , Surround *1 , Surr Back *2*3*4*5
`
Full Band
`
40Hz to 80Hz(THX) to 100Hz , 120Hz , 150Hz ,
200Hz
`
None :
Select if no speaker is connected.
■
Front Wide *1*2*4*6 , Front High *1*2*4*7
`
Full Band
`
40Hz to 80Hz(THX) to 100Hz , 120Hz , 150Hz ,
200Hz
`
None :
Select if no speaker is connected.
Note
*1
“ Full Band ” can be selected only when “ Full Band ” is
selected in the “ Front ” setting.
*2
If the “ Surround ” setting is set to “ None ”, this setting cannot
be selected.
*3
If the “ Surround ” setting is set to anything other than “ Full
Band ”, “ Full Band ” cannot be selected here.
*4
If the “ Speakers Type ” setting is set to “ Bi-Amp ” (
➔
41
), or
Powered Zone 2 is being used (
➔
56 ), this setting cannot be
selected.
*5 If you have selected other than “ Surr Back ” in the “ Surr-
Back/Front High/Front Wide ” setting, this setting cannot be
selected.
*6 If you have selected other than “ Front Wide ” in the “ Front
High/Front Wide/Zone2 ” or “ SurrBack/Front High/Front
Wide ” setting, this setting cannot be selected.
*7 If you have selected other than “ Front High ” in the “ Front
High/Front Wide/Zone2 ” or “ SurrBack/Front High/Front
Wide ” setting, this setting cannot be selected.
■
Surr Back Ch
`
1ch :
Select if only one surround back speaker L is con-
nected.
`
2ch :
Select if two (left and right) surround back speakers
are connected.
Note
• If the “ Surr Back ” Setting is set to “ None ” (
➔
48
), this setting
cannot be selected.