L
27122965
REMOTE
CONTROL
CAUTION: SPEAKER IMPEDANCE
6 OHMS MIN. /SPEAKER
ANTENNA
FM
75
AM
COAXIAL
OPTICAL
1
2
IN
IN
IN
IN
FRONT
SURR
CENTER
SUB
WOOFER
VIDEO 2
VIDEO 1
OUT
DIGITAL INPUT
DVD
MONITOR
OUT
DVD
TAPE
CD
SUBWOOFER
PRE OUT
L
R
FRONT
SPEAKERS
SURROUND
SPEAKERS
CENTER
SPEAKER
R
L
R
L
R
VIDEO 3
VIDEO 2
VIDEO 3
VIDEO 1
VIDEO
OPTICAL
IN
IN
IN
IN
DIGITAL
OUTPUT
IN
INPUT 1
INPUT 2
OUTPUT
COMPONENT VIDEO
P
R
P
B
Y
OUT
OUT
A
B
SURROUND BACK
SPEAKER
DIGITAL
INPUT
L
R
R
L
S VIDEO
AC OUTLETS
AV RECEIVER
MODEL NO.
TX-SR600E
SWITCHED
TOTAL 100W MAX.
AC 230-240 V
50 Hz
4. Memory Preservation
This unit does not require memory preserv ation batteries. A
built-in memory power back-up system preserves the contents
of the memory during po wer f ailures and e ven when the unit is
unplugged. The unit must be plugged in order to char ge the
back-up system.
The memory preserv ation period after the unit has been
unplugged v aries depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a fe w weeks after the last time the unit has been
unplugged. This period is shorter when the unit is e xposed to a
highly humid climate.
2. To initialize the unit
This device employs a microprocessor to perform various
functions and operations. If interference generated by an external
power supply, radio wave, or other electrical source results in
accident which causes the specified operations and functions to
operate abnormally.
To perform a result, please follow the procedure below.
1.Press and hold down the VIDEO-1 button, then press the
STANDBY/ON button.
2.After "clear" is displayed, the preset memory and each
mode stored in the memory, such as surround, are
initialized and will return to the factory setting.
3. Safety-check out
(Only U.S.A. model)
After correcting the original service problem, perform the
following safety check before releasing the set to the customer.
Connect the insulating-resistance tester between the plug of power
supply cord and screw on the back panel.
Specifications: 3.3Mohm+/-10% at 500V.
1. Replacing the fuses
This symbol located near the fuses indicates that the
fuse used is fast operating type. For continued protection against
fire hazard, replace with same type fuse. For fuse rating refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utlise est a rapide.
Pour une protection permanente, n'untiliser que fusibles de
meme type. Ce darnier est la qu le present symbol est
appse.
CIRCUIT NO. PART NO. DESCRIPTION
Note: <D>:120V model only
<O>: Other models except 120V model
<T>: Asian model only for 230V
<R>: Chinese model only
5.Setting the voltage selector (Worldwide models
only)
Worldwide models are equipped with a voltage selector to conform
with local power supplies. Be sure to set this switch to match the
voltage of the power supply in your area before plugging in the unit.
Determine the proper voltage for your area: 220-230 V or 120 V. If
the preset voltage is not correct for your area, insert a screwdriver
into the groove in the switch. Slide the switch all the way to the
upper (120 V) or to the lower (220-230 V), whichever is appropriate.
6.Setting the AM tuning step frequency
(Worldwide models only)
F6901,F6902
F901
F902
F903
F9501
ONT
SURR
CENTER
SUB
WOOFER
VIDEO 1
DVD
L
R
SURROUND
BACK
R
L
PRE OUT
OUT
S
IR
IN
AV RECEIVER
MODEL NO.
TX-SR700E
120 V
220-230 V
120 V
VOLTAGE
SELECTOR
220-230 V
1. Press the MENU button on the front panel or SETUP
button on the remote controller.
The main menu appears.
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
|ENTER|Quit:|SETUP|
2. Use the
and
cursor buttons to select “ 6.
Preference
” and then press the ENTER button.
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
6.Preference
***********************
a.Headphones Level
: 0dB
b.AM Frequency Step
:9 kHz
Quit:|SETUP|
b. AM Frequency Step
This setting only appears on the worldwide model. It determines the
increment amount or decrement amount when adjusting the AM
tuner frequency. The initial setting is 9 kHz, and this needs only to be
changed if you are using the unit in a 10-kHz region.
252199
10A-UL,Fuse <D>
252100
10A-EAK,Fuse <O>
F901
252261
8A-T/UL-ST2,Fuse <D/T/Q/R>
252198 or
8A-UL or
252077,
4A-SE-EAK,
252243 or
4A-SE-TL250V or
252277
4A-SE-TL250V,Fuse <O>
252075,
2.5A-SE-EAK,
252241 or
2.5A-SE-TL250V or
252275
2.5A-SE-TL250V,Fuse <O>
252160 or
2.5A-UL/T-237 or
252254
2.5A-T/UL-ST2,Fuse <D>
252075,
2.5A-SE-EAK,
252241 or
2.5A-SE-TL250V or
252275
2.5A-SE-TL250V,Fuse <O>
TX-SR600/E
SERVICE PROCEDURES
