CDR-205TX
GENERAL INFORMATION-1
DIAGNOSIS
ERROR CODE
Error Code Display for Service.
The CDR-205TX/DX-R700 can display the error codes for service.
1. While pushing the YES key and FINALIZE key, press the DISPLAY key.
2. Turn the JOG(AMCS) key so that "S. Err Disp?" appears on the FL display.
3. Press the ENTER key.
Right 2 FL digits: Error code for service
The error code for service is displayed as a number (ERROR
NUMBER), which follows a message "CHECK DISC" or
"CHECK". For details, see the table below.
Display
Error code table for service
Error code Number (2 digits)
999999yy_
∗∗
Code
Trouble
Contents of Error
Possible Cause
Checkpoints
L
∗
The unit stops during the
tray open/close operation.
(CHECK display)
Improper loading
IC451 (BA5810FP)
E
∗
The unit stops when PLAY
or REC/PAUSE starts.
(CHECK display)
S601 (PSG1014)
IC451 (BA5810FP)
IC401 (CXD2585Q)
P
∗
The unit does not read the
inserted disc, and stops.
(CHECK DISC display)
C
∗
The unit stops before it
enters REC/PAUSE mode.
IC201 (PA9007A)
IC101 (AK8567)
IC308 (TC7S14F)
The unit stops during
playback or recording.
IC451 (BA5810FP)
IC401 (CXD2585Q)
The unit stops in a
recording-related operation,
displaying "CHECK DISC".
If any hardware trouble occurs before
displaying A
∗
or d
∗
, the unit stops
displaying a code other than these
codes. Therefore, these service
codes are generated only for troubles
with the disc.
The unit stops in a recording
related operation, displaying
"CHECK DISC".
The unit does not read the
inserted disc, and stops.
No.
Mechanism Mode
No.
Mechanism Mode
No.
Mechanism Mode
0
1
2
3
4
PLAY
OPEN
STOP
−
−
5
6
7
8
9
SETUP
TOC READ
−
SEARCH
REC/PAUSE
A
B
C
D
E
The indication for
∗
shows the mechanism mode listed below.
PC651
(NJL5809K-F1)
IC451 (BA5810FP)
IC401 (CXD2585Q)
REC
TOC REC
OPC
TOC CHECK
PMA, ACTUAL PAUSE REC
Defective slider
The pickup cannot be returned to the
specified position.
Defect in spindle
Disc upside-down.
Dirty or cracked disc.
Abnormal disc rotation.
No signal obtained from the disc.
Defects related to the recording laser
power
Dirty or cracked disc.
The optimum recording power
cannot be obtained.
Trouble in RF detection.
Defective pickup
Unable to focus because of dirt or
crack on the inserted disc.
Unable to output the proper laser
power.
Unable to focus
Stop during recording.
The unit stops, being obstructed by a
dirt or a crack on the disc.
Defective tray position sensor
Defective loading motor
Improper soldering
Pattern short
Improper power supply
Disconnected flexible cable
Defective drive circuit
Abnormal power supply
Abnormal TOC position switch
Improper soldering
Defective spindle motor
Defective spindle drive circuit
Abnormal FG signals
Defective WBL circuit
Defective decoder circuit
Unable to read ATIP or subcode
High error rate
Defective laser diode
Trouble in RF detection
Defective RFT RFB circuit
Recording power is not sufficient
Improper soldering, pattern short
Trouble with power supply
Unable to read ATIP or subcode
Defective laser diode
Defective focus drive circuits
Defective pickup
Improper soldering
Pattern short
Trouble of power supply
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299